Siemens CU240S DP Operations Instructions Page 65
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Commissioning (software)
2.7 Commissioning modes
Control Units CU240S
Operating Instructions (Compact), 04/2006, A5E00766042B AA
2-45
Parameter Action / Description (Factory setting: bold) Setting
3: Expert: For expert use only
P0010 = 30 Commissioning parameter*
0: Ready
1: Quick commissioning
2: Inverter
30: Factory setting, parameter transfer
95: Safety commissioning (for Safety-Integrated CUs only)
P0803 = 1 Transfer data to EEPROM
0: Disabled
1: Start OP transfer
2: Start MMC Transfer
While the download is active "bUSY" will be displayed on the OP and the inverter will not
react to any commands.
If the download has been completed successfully, P0010 and P0803 will be set to 0 and the
OP display will return to normal.
If the download has failed, F00055 (failure while saving parameter to EEPROM), F00057 (OP
fault) or F00058 (OP contents incompatible) will be displayed.
In this case attempt another download or perform a factory reset to allow the inverter to return
to a known state.
After a successful download the OP can be removed and inserted into another inverter for
download. Then perform the download steps again until the series commissioning has been
completed for all inverters.
2.7.9.3 Series commissioning with STARTER
Upload a parameter set with STARTER
Prerequisites
• An inverter with an apropriate parameter set is available (upload inverter)
• STARTER is installed on the PC used for series commissioning
• Supply voltage is active for the upload inverter
• The upload inverter is in "Ready State".
Connect the STARTER PC via the Option Port (USS on RS232, peer to peer) to the upload
inverter (PC connection Kit requiered), press the online button
and perform the upload by
activating the button
.
Note
Upload with STARTER to MMC
If you want to upload a parameter set with STARTER to an MMC, P0010, P0802 must be set
via the expert list.
- SINAMICS 1
- SINAMICS G120 3
- Table of contents 5
- Table of contents 7
- Installing/Mounting 10
- 1.1 Fitting the CU to the PM 10
- Installing/Mounting 11
- Control settings 13
- Preparation 18
- Screening 18
- Connections 18
- Typical encoder wiring 18
- Commissioning (software) 21
- 2.2 Parameters 22
- 2.2.2 Write parameters 23
- 2.2.3 Monitoring parameters 23
- 2.2.4 Parameter Attributes 23
- 2.2 Parameters 24
- Access level 25
- Change state 25
- Data types 25
- Grouping 26
- Commissioning (software) 27
- 2.2 Parameters 27
- Quick commissioning 28
- Value range 28
- Data sets 28
- 2.3 Factory settings 29
- 2.3 Factory settings 30
- The Operator Panel (OP) 31
- Commissioning with STARTER 34
- STARTER projects 35
- 2.7 Commissioning modes 36
- 2.7 Commissioning modes 37
- 2.7.2 Quick commissioning 38
- 33 39
- 3 3 39
- 33 39
- 2.7 Commissioning modes 40
- Motor identification data 46
- General settings 51
- Pulse Encoder 51
- Temperature Sensor 52
- Selection of command source 52
- Frequency setpoint set 54
- Analog outputs 57
- JOG frequency 58
- Additional Setpoints 58
- Skip Frequency 59
- Ramp times 59
- Rounding 59
- 2.7.9 Series Commissioning 61
- 6,1$0,&6 66
- Automatic Download 69
- Automatic download fault 71
- Reset to the factory setting 73
- 2.8 Encoder Commissioning 74
- Encoder commissioning 75
- Encoder parameterization 76
- 2.8 Encoder Commissioning 77
- 2.8 Encoder Commissioning 78
- 2.8.3 Encoder fault codes 79
- 3.2 Start-up Behavior 81
- Operation 82
- 3.2 Start-up Behavior 82
- Operation 83
- 3.2 Start-up Behavior 83
- PM hotswap with powered CU 87
- CU swap 87
- Successful swap 88
- Swap fault 88
- Upload of parameter sets 89
- Download of parameter sets 89
- Manual download 90
- Automatic download 90
- Service and maintenance 91
- Asia/Pacific (Beijing) 92
- China (Beijing) 92
- Online Service and support 92
- Contact address 92
- Regional contacts 92
- 4.2 Faults and Alarms 93
- 4.3 LED Overview 94
- 4.4 Normal Status LEDs 96
- Service and maintenance 97
- Troubleshooting/FAQs 101
- LED description 102
- Overview 102
- Troubleshooting/FAQs 103
- Standard diagnostics 104
- Legal: 0 … 116 105
- Troubleshooting with the OP 106
- Control Units CU240S 107
- Index 108
Related products and manuals for Power adapters & inverters Siemens CU240S DP
(346 pages)© 2020, manymanuals.com. All rights reserved. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals