Siemens CU240S DP Operations Instructions Page 37
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Commissioning (software)
2.7 Commissioning modes
Control Units CU240S
Operating Instructions (Compact), 04/2006, A5E00766042B AA
2-17
In addition, to carrying-out all of the installation work, an important prerequisite for successful
commissioning is that the Inverter is not disconnected from the line supply while being
parameterized. If a line supply failure interrupts commissioning, then inconsistencies can
occur regarding the parameterization. In this case, it is important that the commissioning is
re-started, possibly with a factory reset to establish the original factory settings.
Notice
Behaviour of inverter on completion of commissioning
The following behaviour should be taken into account when commissioning the inverter:
• standard commissioning with P0014 = 0:
Parameters are only stored in RAM. RAM -> EEPROM can be started:
– with OP: via setting P0971 = 1
– with SATRTER in the online mode: via pressing
RAM -> EEPROM will automatically be performed when starting data transfer from
inverter to MMC (P0802 = 2).
• standard commissioning with P0014 = 1:
All parameter changes will be saved in both RAM and EEPROM.
• While commissioning the fail-safe functions - only possible with a CU240S DP-F - the
relating parameters are automatically stored in RAM and EEPROM
• Data from EEPROM can be transferred to MMC via P0802 = 2.
• Parameters can be changed independent whether an MMC is plugged in or not.
Depending on the settings in P8458 after power cycle the parameters from EEPROM or
MMC are used for start up. The customer has to take of the proper settings of P8458.
– P8458 = 0, no automatic parameter download from the MMC.
– P8458 = 1, automatic parameter download from the MMC only at the first start-up of
the CU with plugged-in MMC
– P8458 = 2, automatic parameter download from the MMC after each start-up of the
CU with plugged-in MMC.
Warning
In case of automatic parameter download from the MMC at start up, F0395 will be
generated.
In standard applications a confirmation test, in fail-safe applications an acceptance test has
to be performed.
- SINAMICS 1
- SINAMICS G120 3
- Table of contents 5
- Table of contents 7
- Installing/Mounting 10
- 1.1 Fitting the CU to the PM 10
- Installing/Mounting 11
- Control settings 13
- Preparation 18
- Screening 18
- Connections 18
- Typical encoder wiring 18
- Commissioning (software) 21
- 2.2 Parameters 22
- 2.2.2 Write parameters 23
- 2.2.3 Monitoring parameters 23
- 2.2.4 Parameter Attributes 23
- 2.2 Parameters 24
- Access level 25
- Change state 25
- Data types 25
- Grouping 26
- Commissioning (software) 27
- 2.2 Parameters 27
- Quick commissioning 28
- Value range 28
- Data sets 28
- 2.3 Factory settings 29
- 2.3 Factory settings 30
- The Operator Panel (OP) 31
- Commissioning with STARTER 34
- STARTER projects 35
- 2.7 Commissioning modes 36
- 2.7 Commissioning modes 37
- 2.7.2 Quick commissioning 38
- 33 39
- 3 3 39
- 33 39
- 2.7 Commissioning modes 40
- Motor identification data 46
- General settings 51
- Pulse Encoder 51
- Temperature Sensor 52
- Selection of command source 52
- Frequency setpoint set 54
- Analog outputs 57
- JOG frequency 58
- Additional Setpoints 58
- Skip Frequency 59
- Ramp times 59
- Rounding 59
- 2.7.9 Series Commissioning 61
- 6,1$0,&6 66
- Automatic Download 69
- Automatic download fault 71
- Reset to the factory setting 73
- 2.8 Encoder Commissioning 74
- Encoder commissioning 75
- Encoder parameterization 76
- 2.8 Encoder Commissioning 77
- 2.8 Encoder Commissioning 78
- 2.8.3 Encoder fault codes 79
- 3.2 Start-up Behavior 81
- Operation 82
- 3.2 Start-up Behavior 82
- Operation 83
- 3.2 Start-up Behavior 83
- PM hotswap with powered CU 87
- CU swap 87
- Successful swap 88
- Swap fault 88
- Upload of parameter sets 89
- Download of parameter sets 89
- Manual download 90
- Automatic download 90
- Service and maintenance 91
- Asia/Pacific (Beijing) 92
- China (Beijing) 92
- Online Service and support 92
- Contact address 92
- Regional contacts 92
- 4.2 Faults and Alarms 93
- 4.3 LED Overview 94
- 4.4 Normal Status LEDs 96
- Service and maintenance 97
- Troubleshooting/FAQs 101
- LED description 102
- Overview 102
- Troubleshooting/FAQs 103
- Standard diagnostics 104
- Legal: 0 … 116 105
- Troubleshooting with the OP 106
- Control Units CU240S 107
- Index 108
Related products and manuals for Power adapters & inverters Siemens CU240S DP
(346 pages)© 2020, manymanuals.com. All rights reserved. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals