Siemens CU240S DP Operations Instructions Page 45
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Commissioning (software)
2.7 Commissioning modes
Control Units CU240S
Operating Instructions (Compact), 04/2006, A5E00766042B AA
2-25
2.7.5 Calculating the motor and control data - flow chart
Performing the calculation of motor and control data via OP
Parameter Description Your setting
P0340 = 1 Calculation of motor parameters
This parameter is required during commissioning in order to optimize the operating behavior of
the inverter. For the complete parameterization (P0340 = 1), in addition to the motor/control
parameters, parameters are pre-assigned which refer to the rated motor data (e.g. torque limits
and reference quantities for interface signals). A list of the parameters, which are calculated,
depending on the setting of P0340, are included in the parameter list.
0: No calculation
1: Complete parameterization
2: Calculation of equivalent circuit data
3: Calculation of V/f and Vector control data
4: Calculation of controller settings only
If additional catalog data is known enter the data in P0341, P0342 and P0344.
P0341 = ? Motor inertia [kg*m
2
]
P0342 = ? Total/motor inertia ratio
P0344 = ? Motor weight (entered in kg)
If the ECD data is known, enter the data in P0350, P0354, P0356, P0358, P0360.
If the ECD data is not known, then: Set P0340 = 4. To calculate the controller settings and skip to END.
P0350 = ? Stator resistance (line-to-line) (entered in Ω)
Stator resistance in Ω of the motor which is connected (from line-to-line). This parameter value
also includes the cable resistance.
P0354 = ? Rotor resistance (entered in Ω)
Defines the rotor resistance of the motor equivalent diagram (phase value).
P0356 = ? Stator leakage inductance (entered in mH)
Defines the stator leakage inductance of the motor equivalent diagram (phase value).
P0358 = ? Rotor leakage inductance (entered in mH)
Defines the rotor leakage inductance of the motor equivalent diagram (phase value).
P0360 = ? Main inductance (entered in mH)
Defines the main (magnetizing) inductance of the motor equivalent diagram (phase value).
P0340 = 3 Calculation of motor parameters
3: Calculation of V/f and Vector control
All of the parameters, dependent on the ECD data are calculated and, in addition, the controller
settings (P0340 = 4).
END The motor parameters have been calculated and it is now possible to return to the additional
parameterization in the Section "Adaptation to the application".
- SINAMICS 1
- SINAMICS G120 3
- Table of contents 5
- Table of contents 7
- Installing/Mounting 10
- 1.1 Fitting the CU to the PM 10
- Installing/Mounting 11
- Control settings 13
- Preparation 18
- Screening 18
- Connections 18
- Typical encoder wiring 18
- Commissioning (software) 21
- 2.2 Parameters 22
- 2.2.2 Write parameters 23
- 2.2.3 Monitoring parameters 23
- 2.2.4 Parameter Attributes 23
- 2.2 Parameters 24
- Access level 25
- Change state 25
- Data types 25
- Grouping 26
- Commissioning (software) 27
- 2.2 Parameters 27
- Quick commissioning 28
- Value range 28
- Data sets 28
- 2.3 Factory settings 29
- 2.3 Factory settings 30
- The Operator Panel (OP) 31
- Commissioning with STARTER 34
- STARTER projects 35
- 2.7 Commissioning modes 36
- 2.7 Commissioning modes 37
- 2.7.2 Quick commissioning 38
- 33 39
- 3 3 39
- 33 39
- 2.7 Commissioning modes 40
- Motor identification data 46
- General settings 51
- Pulse Encoder 51
- Temperature Sensor 52
- Selection of command source 52
- Frequency setpoint set 54
- Analog outputs 57
- JOG frequency 58
- Additional Setpoints 58
- Skip Frequency 59
- Ramp times 59
- Rounding 59
- 2.7.9 Series Commissioning 61
- 6,1$0,&6 66
- Automatic Download 69
- Automatic download fault 71
- Reset to the factory setting 73
- 2.8 Encoder Commissioning 74
- Encoder commissioning 75
- Encoder parameterization 76
- 2.8 Encoder Commissioning 77
- 2.8 Encoder Commissioning 78
- 2.8.3 Encoder fault codes 79
- 3.2 Start-up Behavior 81
- Operation 82
- 3.2 Start-up Behavior 82
- Operation 83
- 3.2 Start-up Behavior 83
- PM hotswap with powered CU 87
- CU swap 87
- Successful swap 88
- Swap fault 88
- Upload of parameter sets 89
- Download of parameter sets 89
- Manual download 90
- Automatic download 90
- Service and maintenance 91
- Asia/Pacific (Beijing) 92
- China (Beijing) 92
- Online Service and support 92
- Contact address 92
- Regional contacts 92
- 4.2 Faults and Alarms 93
- 4.3 LED Overview 94
- 4.4 Normal Status LEDs 96
- Service and maintenance 97
- Troubleshooting/FAQs 101
- LED description 102
- Overview 102
- Troubleshooting/FAQs 103
- Standard diagnostics 104
- Legal: 0 … 116 105
- Troubleshooting with the OP 106
- Control Units CU240S 107
- Index 108
Related products and manuals for Power adapters & inverters Siemens CU240S DP
(346 pages)© 2020, manymanuals.com. All rights reserved. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals