Siemens CU240S DP Operations Instructions Page 61
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Commissioning (software)
2.7 Commissioning modes
Control Units CU240S
Operating Instructions (Compact), 04/2006, A5E00766042B AA
2-41
Finishing the application setting
Parameter Description (Factory setting: bold) Setting
P0971 = 1 Transfer data from RAM to EEPROM
0: Disabled
1: Start data transfer, RAM → EEPROM
All of the parameter changes are transferred from the RAM into the EEPROM which means
that they are saved in a non-volatile state within the Inverter (data is not lost when the power
fails).
While the transfer is active, "bUSY" will be displayed on the OP. Once the transfer is
completed P0970 will be set internally to "0" and the "P0970" will be displayed.
2.7.9 Series Commissioning
2.7.9.1 Series commissioning
Overview
Series commissioning means the possibility to transfer the parameter set from one inverter
into a number of other inverters which allows fast commissioning for identical applications
(for example series machines or group inverters).
The series commissioning is divided into the following steps:
• create a proper parameter set
• upload this parameter set
• download of the uploaded parameter set into the new inverter
To perform series commissioning an appropriate parameter set must be available. This
parameter set can be created by parameterizing an Inverter via OP or STARTER.
Caution
Parameter download between different types of control units and of different firmware
versions is not recommended.
Basically, it is possible to download parameter sets off different CU types, however, as the
parameter sets might differ, the user is fully responsible for the consistency of the
downloaded parameter set.
Therefore, the customer has to confirm his responsibility in case of an automatic download
by acknowledging F0395.
Once an inverter with an appropriate parameter set is available, the parameter set can be
uploaded and in the next step downloaded into the new inverter via OP, STARTER or MMC.
The various interfaces are shown in the figure below.
- SINAMICS 1
- SINAMICS G120 3
- Table of contents 5
- Table of contents 7
- Installing/Mounting 10
- 1.1 Fitting the CU to the PM 10
- Installing/Mounting 11
- Control settings 13
- Preparation 18
- Screening 18
- Connections 18
- Typical encoder wiring 18
- Commissioning (software) 21
- 2.2 Parameters 22
- 2.2.2 Write parameters 23
- 2.2.3 Monitoring parameters 23
- 2.2.4 Parameter Attributes 23
- 2.2 Parameters 24
- Access level 25
- Change state 25
- Data types 25
- Grouping 26
- Commissioning (software) 27
- 2.2 Parameters 27
- Quick commissioning 28
- Value range 28
- Data sets 28
- 2.3 Factory settings 29
- 2.3 Factory settings 30
- The Operator Panel (OP) 31
- Commissioning with STARTER 34
- STARTER projects 35
- 2.7 Commissioning modes 36
- 2.7 Commissioning modes 37
- 2.7.2 Quick commissioning 38
- 33 39
- 3 3 39
- 33 39
- 2.7 Commissioning modes 40
- Motor identification data 46
- General settings 51
- Pulse Encoder 51
- Temperature Sensor 52
- Selection of command source 52
- Frequency setpoint set 54
- Analog outputs 57
- JOG frequency 58
- Additional Setpoints 58
- Skip Frequency 59
- Ramp times 59
- Rounding 59
- 2.7.9 Series Commissioning 61
- 6,1$0,&6 66
- Automatic Download 69
- Automatic download fault 71
- Reset to the factory setting 73
- 2.8 Encoder Commissioning 74
- Encoder commissioning 75
- Encoder parameterization 76
- 2.8 Encoder Commissioning 77
- 2.8 Encoder Commissioning 78
- 2.8.3 Encoder fault codes 79
- 3.2 Start-up Behavior 81
- Operation 82
- 3.2 Start-up Behavior 82
- Operation 83
- 3.2 Start-up Behavior 83
- PM hotswap with powered CU 87
- CU swap 87
- Successful swap 88
- Swap fault 88
- Upload of parameter sets 89
- Download of parameter sets 89
- Manual download 90
- Automatic download 90
- Service and maintenance 91
- Asia/Pacific (Beijing) 92
- China (Beijing) 92
- Online Service and support 92
- Contact address 92
- Regional contacts 92
- 4.2 Faults and Alarms 93
- 4.3 LED Overview 94
- 4.4 Normal Status LEDs 96
- Service and maintenance 97
- Troubleshooting/FAQs 101
- LED description 102
- Overview 102
- Troubleshooting/FAQs 103
- Standard diagnostics 104
- Legal: 0 … 116 105
- Troubleshooting with the OP 106
- Control Units CU240S 107
- Index 108
Related products and manuals for Power adapters & inverters Siemens CU240S DP
(346 pages)© 2020, manymanuals.com. All rights reserved. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals