Siemens CU240S DP Operations Instructions Page 64
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Commissioning (software)
2.7 Commissioning modes
Control Units CU240S
2-44 Operating Instructions (Compact), 04/2006, A5E00766042B AA
To copy a parameter set from one inverter to another, the following procedure should be
performed.
Upload a parameter set with an OP
Prerequisites
• An inverter with an apropriate parameter set is available (upload inverter)
• Supply voltage is active for the upload inverter
• The upload inverter is in "Ready State".
Parameter Action / Description (Factory setting: bold) Setting
Fit the OP to the Inverter - for the parameter set to be uploaded, perform the following steps:
P0003 = 3 User access level*
1: Standard: Allows access into most frequently used parameters
2: Extended: Allows extended access e.g. to inverter I/O functions
3: Expert: For expert use only
P0010 = 30 Commissioning parameter*
0: Ready
1: Quick commissioning
2: Inverter
30: Factory setting, parameter transfer
95: Commissioning the fail-safe functions (CUs with Safety-Integrated functions only)
P0802 = 1 Transfer data from EEPROM
0: Disabled
1: Start OP transfer
2: Start MMC Transfer
While the upload is active "bUSY" will be displayed on the OP and the inverter will not react to
any commands.
If the upload has been completed successfully, P0010 and P0802 will be set to 0 and the OP
display will return to normal.
If the upload has failed, F00055 (failure while saving parameter on OP) or F00057 (OP fault)
will be displayed.
In this case attempt another download or perform a factory reset.
After a successful upload disconnect the OP from the upload inverter.
Download a parameter set with an OP
Prerequisites
• Supply voltage is active for the download inverter
• The download inverter is in "Ready State".
Parameter Action / Description (Factory setting: bold) Setting
Fit the OP to the inverter and perform the download according the flow chart.
P0003 = 3 User access level*
1: Standard: Allows access to the most frequently used parameters
2: Extended: Allows extended access e.g. to inverter I/O functions
- SINAMICS 1
- SINAMICS G120 3
- Table of contents 5
- Table of contents 7
- Installing/Mounting 10
- 1.1 Fitting the CU to the PM 10
- Installing/Mounting 11
- Control settings 13
- Preparation 18
- Screening 18
- Connections 18
- Typical encoder wiring 18
- Commissioning (software) 21
- 2.2 Parameters 22
- 2.2.2 Write parameters 23
- 2.2.3 Monitoring parameters 23
- 2.2.4 Parameter Attributes 23
- 2.2 Parameters 24
- Access level 25
- Change state 25
- Data types 25
- Grouping 26
- Commissioning (software) 27
- 2.2 Parameters 27
- Quick commissioning 28
- Value range 28
- Data sets 28
- 2.3 Factory settings 29
- 2.3 Factory settings 30
- The Operator Panel (OP) 31
- Commissioning with STARTER 34
- STARTER projects 35
- 2.7 Commissioning modes 36
- 2.7 Commissioning modes 37
- 2.7.2 Quick commissioning 38
- 33 39
- 3 3 39
- 33 39
- 2.7 Commissioning modes 40
- Motor identification data 46
- General settings 51
- Pulse Encoder 51
- Temperature Sensor 52
- Selection of command source 52
- Frequency setpoint set 54
- Analog outputs 57
- JOG frequency 58
- Additional Setpoints 58
- Skip Frequency 59
- Ramp times 59
- Rounding 59
- 2.7.9 Series Commissioning 61
- 6,1$0,&6 66
- Automatic Download 69
- Automatic download fault 71
- Reset to the factory setting 73
- 2.8 Encoder Commissioning 74
- Encoder commissioning 75
- Encoder parameterization 76
- 2.8 Encoder Commissioning 77
- 2.8 Encoder Commissioning 78
- 2.8.3 Encoder fault codes 79
- 3.2 Start-up Behavior 81
- Operation 82
- 3.2 Start-up Behavior 82
- Operation 83
- 3.2 Start-up Behavior 83
- PM hotswap with powered CU 87
- CU swap 87
- Successful swap 88
- Swap fault 88
- Upload of parameter sets 89
- Download of parameter sets 89
- Manual download 90
- Automatic download 90
- Service and maintenance 91
- Asia/Pacific (Beijing) 92
- China (Beijing) 92
- Online Service and support 92
- Contact address 92
- Regional contacts 92
- 4.2 Faults and Alarms 93
- 4.3 LED Overview 94
- 4.4 Normal Status LEDs 96
- Service and maintenance 97
- Troubleshooting/FAQs 101
- LED description 102
- Overview 102
- Troubleshooting/FAQs 103
- Standard diagnostics 104
- Legal: 0 … 116 105
- Troubleshooting with the OP 106
- Control Units CU240S 107
- Index 108
Related products and manuals for Power adapters & inverters Siemens CU240S DP
(346 pages)© 2020, manymanuals.com. All rights reserved. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals