Siemens HF 35M 562 B Specifications Page 187
- Page / 262
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Device functions
SIMATIC - ET 200pro motor starters
GWA 4NEB 950 5661-02 DS 06
10-49
10.18.3 Plausibility check of data
Description
The motor starter checks all incoming parameters for validity and plausibility.
In the case of incorrect parameters
• during a startup (after power ON) the messages ’Group fault’ and ’Incorrect
parameter value’ are set.
Motor and brake output remain switched off.
• in ongoing operation, the messages ’Incorrect parameter value’ or ’Parame-
terization in ON status not permitted’ are set. ’Group fault’ is not set.
Motor and brake output are not switched off.
10.18.4 Output of messages
This device function delivers the following messages:
Messages Meaning
General messages
Ready (automatic) Device can be operated via host (e.g. PLC)
Group fault At least 1 fault is set.
General warning At least 1 warning exists
Process image fault Process image of the outputs contains
nonallowable bit combination, e.g. ’Motor
cw’ and ’Motor ccw’ set simultaneously
Field bus connection
Bus fault Device has no rear wall bus communica-
tion (ESSA3 interface to the controller
interrupted)
CPU/master STOP PLC program no longer being processed
Acknowledgement
Trip reset completed Trip teset accepted, i.e. fault has been
acknowledged.
Trip reset not possible Unable to acknowledge fault as the reason
for the shutdown is still present.
Operating type monitoring
Automatic operating mode Automatic (PLC control)
Manual bus operating mode Manual operation via field bus
(B&B control)
Manual local operating mode Manual operation via local device interface
(B&B control)
Lost connection in manual operating mode During manual operation, the associated
communication connection was inter-
rupted for longer than 5 seconds.
Table 10-32: Communication – Messages
- Release 07/2011 1
- Safety guidelines 2
- Qualified personnel 2
- Correct usage 2
- Preface 3
- Certification 4
- Disclaimer of liability 4
- Table of contents 7
- GWA 4NEB 950 5661-02 DS 06 10
- Ta b l e s 15
- Description 1 19
- 1.1.2 Special modules 20
- 1.1.3 Motor starters 21
- 1.1.4 Accessories 22
- ET 200pro with motor starters 24
- Parts list 25
- 1.4 PROFIenergy 27
- Brief instructions 2 31
- 2.2 ET 200pro components 32
- 2.3 Requirements 33
- 2.4 Installation 33
- Mounting order 34
- Brief instructions 35
- 2.5 Cabling and fitting 36
- 2.6 Configuration 37
- 2.8 Activation 39
- Checking the wiring 40
- 2.9 Diagnostic options 41
- 2.10 Help 43
- Installation 3 45
- Installation position 46
- Please note: 46
- Installation 47
- 3.3 Derating 48
- Features 50
- Requirements 50
- 4.1 Commissioning 57
- 4.2 Configuration 59
- Software update 60
- 4.3 Diagnostics 61
- Commissioning and diagnostics 62
- 4.4 LED indicators 63
- 4.5 Process image 67
- Input signals 68
- Output signals 69
- Log book entries 70
- Measurements (DS 94) 70
- Statistics data (DS 95) 71
- Slave pointer (DS 96) 71
- Device diagnostics 73
- Application 74
- Order Numbers 74
- °C to +70°C 75
- Rear wall bus modules 6 77
- Rear wall bus modules 78
- Special modules 7 79
- Special modules 80
- 7.2.1 Features 80
- 7.2.3 Circuit diagram 81
- 7.3.2 Description 83
- 7.3.4 Circuit diagram 85
- 7.3.5 Connection technology 85
- Configuration 86
- 7.4.1 Features 88
- 7.4.2 Description 88
- 7.4.4 Circuit diagram 89
- 7. 5 P o w e r b u s 91
- 7.6.1 Parameters 92
- Motor starters 8 95
- 8.1.2 Electronic starters 96
- 8.2 Motor starter properties 97
- 8.2.6 Connection technology 100
- Auxiliary circuits 101
- Motor starters 102
- 8.2.7 Parameters 104
- 8.3.1 Physical principles 111
- Starting current 111
- Star delta starter 112
- Reducing the starting current 112
- 8.3.2 Application and use 115
- Applications 115
- 8.3.3 Features 116
- Current limiting value 118
- Cyclic duration factor CD 118
- Switching frequency 118
- 8.3.4 Notes on configuration 126
- Starting torque 126
- Criteria for selection 127
- Starting time 128
- Site altitude 128
- Connection 9 129
- 9.1 Rules for wiring 130
- 9.2 Energy cable preparation 131
- Other Station 132
- Connector set 133
- 9-pin (pin) 133
- MS MS MS MS 133
- Motor connection cable 133
- Connection 134
- 9.3 Energy jumper plug 137
- Device functions 10 139
- 10.2 Basic parameters 140
- Actual motor current 141
- Load type 141
- 10.2.2 Parameter – settings 142
- 10.3 Thermal motor model 143
- Device functions 144
- Messages and actions 147
- 10.4 Current limits 149
- Range: 1 second to 5 seconds 150
- Motor continues to operate 151
- Motor is shut down 151
- 10.4.3 Messages and actions 152
- 10.4.4 Temperature sensor 153
- Temperature sensor 153
- Temperature sensor monitoring 154
- 10.5 Asymmetry 156
- 10.6 Trip reset 157
- Input n level 159
- Input n action 159
- Quick stop 162
- Cold run 164
- 10.7.3 Messages and actions 166
- Description 167
- 10.9 Field bus interface 170
- Replacement value 171
- L1 L2 L3 172
- 10.10.1 Device parameters 173
- Priorities regulation 173
- 10.10.2 Parameters – settings 174
- 10.10.3 Message 174
- 10.11 Self-test 175
- Self-test fault 176
- 10.11.1 Messages 176
- 10.12 Emergency start 177
- 10.13 Factory setting 178
- 10.14 Maintenance 179
- 10.15.1 Device parameters 180
- 10.15.2 Parameters – settings 180
- 10.15.3 Messages 180
- Electronic switch technology 181
- 10.16.1 Messages and actions 181
- 10.17 Local device interface 182
- 10.18 Communication 183
- Operating modes 184
- Connection monitoring 185
- 10.18.2 Commands 186
- Commands and their meaning 186
- 10.18.4 Output of messages 187
- 10.19 PROFIenergy 189
- 10.20 Log book 193
- Log book - trips 194
- Log book - events 194
- Log book - device faults 194
- Order numbers A 195
- Adjustment range Order number 196
- Dimensioned drawings B 199
- B.3 400 V shutdown module 201
- Applications C 205
- C.1 Standard applications 206
- C.1.2 No repair switch module 208
- C.1.3 For hot swapping 210
- C.2 SAFETY applications 212
- D.1 Data formats 219
- Data formats and data records 220
- D.2 Fault codes 221
- Fault codes 222
- D.3 Data records 223
- D.5.6 DS93 – Write command 236
- D.6 DS95 - Read statistics 239
- D.6.1 DS96 – Slave pointer 240
- D.7 Device parameters 244
- D.7.2 DS134 – Maintenance 252
- D.8 I&M data 253
- Glossary 255
- Motor starters; High feature 256
- Motor starters; standard 256
- MS (motor starter) 256
- Reversing starters 256
Related products and manuals for Microwaves Siemens HF 35M 562 B
Microwaves Siemens HF 35M 562 B User Manual
(92 pages)
(92 pages)
Microwaves Siemens HF 17056 User Manual
(31 pages)
(31 pages)
Microwaves Siemens HF25M5L2 User Manual
(172 pages)
(172 pages)
Microwaves Siemens HF25G5L2 User Manual
(204 pages)
(204 pages)
Microwaves Siemens HF35M630 User Manual
(124 pages)
(124 pages)
Microwaves Siemens HF36V306 User Manual
(32 pages)
(32 pages)
Microwaves Siemens HF35M630 User Manual
(1 pages)
(1 pages)
Microwaves Siemens HF25C530 User Manual
(44 pages)
(44 pages)
Microwaves Siemens HB84K552 User Manual
(36 pages)
(36 pages)
Microwaves Siemens HB38D585 User Manual
(36 pages)
(36 pages)
Microwaves Siemens HB38G4580 User Manual
(40 pages)
(40 pages)
Microwaves Siemens HB84K552 User Manual
(32 pages)
(32 pages)
Microwaves Siemens HB33GB550 User Manual
(28 pages)
(28 pages)
Microwaves Siemens HB38D585 User Manual
(40 pages)
(40 pages)
Microwaves Siemens HB84K552 User Manual
(6 pages)
(6 pages)
Microwaves Siemens HB33GB550 User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals