Siemens HF 35M 562 B Specifications Page 145
- Page / 262
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Device functions
SIMATIC - ET 200pro motor starters
GWA 4NEB 950 5661-02 DS 06
10-7
Recovery time (can only be parameterized with high feature motor starters)
The ’recovery time’ is the time defined for cooling after which a reset is possible
following an overload trip.
Trip reset signals received during the recovery time (DO 0.3) have no effect.
The motor starters are set to the following times:
• with DSe ST, RSe ST:
Setting fixed to 90 s.
• with DSe HF, RSe HF, sDSSte / sDSte and sRSSte / sRSte:
The recovery time after overload tripping is at least 1 minute. The recovery
time can be parameterized and can be changed between 60 seconds and
1800 seconds.
Factory setting: 90 seconds
Power failures during this time extend the time specifications accordingly
when the basic ’Non-resetting on voltage failure’ parameter is active.
Prewarning limit value for motor heating
This parameter can be used to specify a percentage motor heating process
as a prewarning limit. The motor starter issues a warning if the parameterized
motor heating limit is exceeded. A shutdown is implemented at 100 %.
Range: 0 % to 95 %.
Prewarning limit value time-based trigger reserve
This parameter can be used to specify a time as a prewarning limit. The motor
starter warns against an impending overload shutdown within the parameter-
ized time if the current operating conditions are observed.
Range: 0 seconds to 500 seconds.
- Release 07/2011 1
- Safety guidelines 2
- Qualified personnel 2
- Correct usage 2
- Preface 3
- Certification 4
- Disclaimer of liability 4
- Table of contents 7
- GWA 4NEB 950 5661-02 DS 06 10
- Ta b l e s 15
- Description 1 19
- 1.1.2 Special modules 20
- 1.1.3 Motor starters 21
- 1.1.4 Accessories 22
- ET 200pro with motor starters 24
- Parts list 25
- 1.4 PROFIenergy 27
- Brief instructions 2 31
- 2.2 ET 200pro components 32
- 2.3 Requirements 33
- 2.4 Installation 33
- Mounting order 34
- Brief instructions 35
- 2.5 Cabling and fitting 36
- 2.6 Configuration 37
- 2.8 Activation 39
- Checking the wiring 40
- 2.9 Diagnostic options 41
- 2.10 Help 43
- Installation 3 45
- Installation position 46
- Please note: 46
- Installation 47
- 3.3 Derating 48
- Features 50
- Requirements 50
- 4.1 Commissioning 57
- 4.2 Configuration 59
- Software update 60
- 4.3 Diagnostics 61
- Commissioning and diagnostics 62
- 4.4 LED indicators 63
- 4.5 Process image 67
- Input signals 68
- Output signals 69
- Log book entries 70
- Measurements (DS 94) 70
- Statistics data (DS 95) 71
- Slave pointer (DS 96) 71
- Device diagnostics 73
- Application 74
- Order Numbers 74
- °C to +70°C 75
- Rear wall bus modules 6 77
- Rear wall bus modules 78
- Special modules 7 79
- Special modules 80
- 7.2.1 Features 80
- 7.2.3 Circuit diagram 81
- 7.3.2 Description 83
- 7.3.4 Circuit diagram 85
- 7.3.5 Connection technology 85
- Configuration 86
- 7.4.1 Features 88
- 7.4.2 Description 88
- 7.4.4 Circuit diagram 89
- 7. 5 P o w e r b u s 91
- 7.6.1 Parameters 92
- Motor starters 8 95
- 8.1.2 Electronic starters 96
- 8.2 Motor starter properties 97
- 8.2.6 Connection technology 100
- Auxiliary circuits 101
- Motor starters 102
- 8.2.7 Parameters 104
- 8.3.1 Physical principles 111
- Starting current 111
- Star delta starter 112
- Reducing the starting current 112
- 8.3.2 Application and use 115
- Applications 115
- 8.3.3 Features 116
- Current limiting value 118
- Cyclic duration factor CD 118
- Switching frequency 118
- 8.3.4 Notes on configuration 126
- Starting torque 126
- Criteria for selection 127
- Starting time 128
- Site altitude 128
- Connection 9 129
- 9.1 Rules for wiring 130
- 9.2 Energy cable preparation 131
- Other Station 132
- Connector set 133
- 9-pin (pin) 133
- MS MS MS MS 133
- Motor connection cable 133
- Connection 134
- 9.3 Energy jumper plug 137
- Device functions 10 139
- 10.2 Basic parameters 140
- Actual motor current 141
- Load type 141
- 10.2.2 Parameter – settings 142
- 10.3 Thermal motor model 143
- Device functions 144
- Messages and actions 147
- 10.4 Current limits 149
- Range: 1 second to 5 seconds 150
- Motor continues to operate 151
- Motor is shut down 151
- 10.4.3 Messages and actions 152
- 10.4.4 Temperature sensor 153
- Temperature sensor 153
- Temperature sensor monitoring 154
- 10.5 Asymmetry 156
- 10.6 Trip reset 157
- Input n level 159
- Input n action 159
- Quick stop 162
- Cold run 164
- 10.7.3 Messages and actions 166
- Description 167
- 10.9 Field bus interface 170
- Replacement value 171
- L1 L2 L3 172
- 10.10.1 Device parameters 173
- Priorities regulation 173
- 10.10.2 Parameters – settings 174
- 10.10.3 Message 174
- 10.11 Self-test 175
- Self-test fault 176
- 10.11.1 Messages 176
- 10.12 Emergency start 177
- 10.13 Factory setting 178
- 10.14 Maintenance 179
- 10.15.1 Device parameters 180
- 10.15.2 Parameters – settings 180
- 10.15.3 Messages 180
- Electronic switch technology 181
- 10.16.1 Messages and actions 181
- 10.17 Local device interface 182
- 10.18 Communication 183
- Operating modes 184
- Connection monitoring 185
- 10.18.2 Commands 186
- Commands and their meaning 186
- 10.18.4 Output of messages 187
- 10.19 PROFIenergy 189
- 10.20 Log book 193
- Log book - trips 194
- Log book - events 194
- Log book - device faults 194
- Order numbers A 195
- Adjustment range Order number 196
- Dimensioned drawings B 199
- B.3 400 V shutdown module 201
- Applications C 205
- C.1 Standard applications 206
- C.1.2 No repair switch module 208
- C.1.3 For hot swapping 210
- C.2 SAFETY applications 212
- D.1 Data formats 219
- Data formats and data records 220
- D.2 Fault codes 221
- Fault codes 222
- D.3 Data records 223
- D.5.6 DS93 – Write command 236
- D.6 DS95 - Read statistics 239
- D.6.1 DS96 – Slave pointer 240
- D.7 Device parameters 244
- D.7.2 DS134 – Maintenance 252
- D.8 I&M data 253
- Glossary 255
- Motor starters; High feature 256
- Motor starters; standard 256
- MS (motor starter) 256
- Reversing starters 256
Related products and manuals for Microwaves Siemens HF 35M 562 B
Microwaves Siemens HF 35M 562 B User Manual
(92 pages)
(92 pages)
Microwaves Siemens HF 17056 User Manual
(31 pages)
(31 pages)
Microwaves Siemens HF25M5L2 User Manual
(172 pages)
(172 pages)
Microwaves Siemens HF25G5L2 User Manual
(204 pages)
(204 pages)
Microwaves Siemens HF35M630 User Manual
(124 pages)
(124 pages)
Microwaves Siemens HF36V306 User Manual
(32 pages)
(32 pages)
Microwaves Siemens HF35M630 User Manual
(1 pages)
(1 pages)
Microwaves Siemens HF25C530 User Manual
(44 pages)
(44 pages)
Microwaves Siemens HB84K552 User Manual
(36 pages)
(36 pages)
Microwaves Siemens HB38D585 User Manual
(36 pages)
(36 pages)
Microwaves Siemens HB38G4580 User Manual
(40 pages)
(40 pages)
Microwaves Siemens HB84K552 User Manual
(32 pages)
(32 pages)
Microwaves Siemens HB33GB550 User Manual
(28 pages)
(28 pages)
Microwaves Siemens HB38D585 User Manual
(40 pages)
(40 pages)
Microwaves Siemens HB84K552 User Manual
(6 pages)
(6 pages)
Microwaves Siemens HB33GB550 User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals