Siemens TC63 User Manual Page 72
- Page / 501
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TC63 AT Command Set
3.3 AT^SIND
s
TC63_ATC_V00.490 Page 72 of 501 5/24/05
Confidential / Draft - Do not copy
Unsolicited Result Codes
URC 1
Format of the standard indicator:
+CIEV: <indDescr>, <indValue>
Value related to an indicator has changed.
URC 2
Format of the "adnread" indicator issued when accessing the ADN phonebook records stored on the SIM:
+CIEV: <indDescr>, <adnEntry>, <adnNumber>, <adnType>, <adnText>
+CIEV: <indDescr>, "READY"
One URC is issued for every used Abbreviated Dialing Number (ADN) phonebook record. After the last record
of the ADN phonebook was read, a URC with "READY" tag signals end of processing.
URC 3
Format of the Voice Message indicator, if the number of waiting messages is delivered by the network:
+CIEV: <indDescr>, <indValue>, <vmCounter>
If the number of waiting messages is not delivered the standard indicator applies.
URC 4
Format of the "eons" indicator:
+CIEV: <indDescr>, <indValue>, <eonsOperator>, <servProvider>
One URC is issued for each new LAI (Location Area Information) broadcast by the network.
URC 5
Format of the "nitz" indicator:
+CIEV: <indDescr>, <nitzUT>, <nitzTZ>, <nitzDST>
Parameter Description
String values and their <indValue> ranges.
All indicators supported by AT+CIND are accessible with this command, too. A detailed description of these indi-
cators can be found there.
The following indicators are accessible via AT^SIND only:
“audio“ Activity of the built-in audio unit.
“vmwait1“ Voice Message Waiting Indication for line 1
"vmwait1" and "vmwait2" indicate the receipt of a special short message with
a Voice Message Waiting Indicator. The service must be provisioned by the
operator.
The numbers 1 or 2 in "vmwait1" and "vmwait2" are related to the two lines of
the Alternate Line Service (ALS), also defined in CPHS Phase 2 standard. For
further details refer to the AT^SALS command.
The presentation mode of the indicator varies with the operator: If more than
one message are waiting, some operators only indicate the first one, others
deliver the indicator each time a new voice message is put into the mailbox.
<indDescr>
(str)
0 Audio unit not active.
1 Value 1 means for example:
Outgoing voice call: Indicator appears when dialing starts.
Incoming voice call: Indicator appears prior to the RING result code.
0 The value 0 notifies that no new voice message is available, and is pro-
vided by the service center to clear the voice message indication after
the subscriber has retrieved all voice messages.
1 The value 1 notifies the subscriber that the mailbox contains one or
several messages.
- AT Command Set 1
- Contents 3
- TC63 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 32
- 3. Status Control Commands 66
- 3.2 AT+CIND Indicator control 68
- 4.1 AT\Q Flow control 89
- 4.5 ATE Enable command echo 93
- 4.9.1 Autobauding 101
- 5. Security Commands 108
- 5.4 AT+CLCK Facility lock 118
- 5.5 AT^SLCK Facility lock 123
- 5.6 AT+CPWD Change Password 124
- 5.7 AT^SPWD Change Password 128
- 5.8 AT^SCSL Customer SIM Lock 130
- 6. Identification Commands 134
- 7. Call related Commands 140
- 7.2 ATA Answer a call 141
- 7.10 AT+CHUP Hang up call 151
- 7.29 ATP Select pulse dialing 178
- 7.30 ATT Select tone dialing 178
- 8. Network Service Commands 179
- 8.5 AT+CSQ Signal quality 187
- 8.6 AT^SMONC Cell Monitoring 188
- 8.7 AT^SMOND Cell Monitoring 190
- 8.8.1 AT^MONI responses 194
- 8.8.2 Service states 195
- 8.9.1 AT^MONP responses 197
- 8.10 AT^SMONG GPRS Monitor 198
- 8.12 AT^SHOM Display Homezone 202
- 9.5 AT+CCUG Closed User Group 212
- 9.7 AT+CCWA Call Waiting 218
- 10. Internet Service Commands 235
- Remote Client 257
- 11. GPRS Commands 268
- 12. FAX Commands 311
- 12.4 AT+FRM Receive Data 314
- 12.5 AT+FRS Receive Silence 315
- 12.7 AT+FTM Transmit Data 317
- 13.1 SMS parameters 319
- 13.7 AT+CMGS Send SMS message 331
- 14. SIM related Commands 363
- 15.3 Related AT Commands 384
- 16.2 ^SSTN SAT Notification 388
- 16.4 AT^SSTR SAT Response 390
- 17. Phonebook Commands 391
- 17.2 AT+CNUM Read own numbers 392
- 18. Audio Commands 411
- 18.5 AT+CMUT Mute control 414
- 18.6 AT+VTD Tone duration 415
- 19. Hardware related Commands 436
- 19.2 AT+CALA Set alarm time 437
- 19.7.4 Example: Using I²C Bus 456
- 20. Miscellaneous Commands 457
- 21. Appendix 462
Related products and manuals for Hardware Siemens TC63
Hardware Siemens BC-16 User Manual
(2 pages)
(2 pages)
Hardware Siemens 54 User Manual
(56 pages)
(56 pages)
Hardware Siemens 300 User Manual
(64 pages)
(64 pages)
Hardware Siemens CL-110-I User Manual
(129 pages)
(129 pages)
Hardware Siemens CP 1515 User Manual
(299 pages)
(299 pages)
Hardware Siemens I-SURF User Manual
(70 pages)
(70 pages)
Hardware Siemens C2-010 User Manual
(51 pages)
(51 pages)
Hardware Siemens TC35 User Manual
(39 pages)
(39 pages)
Hardware Siemens S5-135U/155U User Manual
(54 pages)
(54 pages)
Hardware Siemens TC35i User Manual
(37 pages)
(37 pages)
© 2020, manymanuals.com. All rights reserved. | 0.154 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals