Siemens TC63 User Manual Page 450
- Page / 501
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TC63 AT Command Set
19.7 AT^SSPI
s
TC63_ATC_V00.490 Page 450 of 501 5/24/05
Confidential / Draft - Do not copy
19.7 AT^SSPI Serial Protocol Interface
The AT^SSPI command enables the module to be connected to external I²C devices. The I²C datastream is
mapped through an internal I²C driver to and from an ASCII hex protocol which can be exchanged with an exter-
nal application via V24.
The AT^SSPI write command configures and activates the I²C interface and changes from command mode into
data mode. All values must be given in hexadecimal format (0 - 9, A - F) without "0x". For details on data mode
please refer to Section 19.7.2, Transmitting Data over AT Interface.
Syntax
Parameter Description
Parameter returned by the AT^SSPI? read command.
Indicates whether or not the I²C channel is used. When the channel is open and the ME is in data mode, the
read command can only be used if one of the remaining interfaces is available. For example, when the channel
was opened on ASC0, you can use ASC1, MUX channels or USB to check the status.
[0]
(&F)
Not connected (channel closed). All following parameters are the factory set-
tings AT^SSPI=0,0010,0000,0000.
1 Connected (channel open, ME in data mode). All following parameters are the
values currently used, for example AT^SSPI=1,0010,FFFF,FFFF.
Parameter <basicConfiguration> is a 16 bit word which contains four subparameters to control the follow-
ing functions:
Test Command
AT^SSPI=?
Response(s)
^SSPI:(list of supported <basicConfiguration>s), (list of supported <delayOne>s), (list of supported
<delayTwo>s)
OK
Read Command
AT^SSPI?
Response(s)
^SSPI: <connectionState>, <basicConfiguration>, <delayOne>, <delayTwo>
OK
ERROR
+CME ERROR: <err>
Write Command
AT^SSPI=[<basicConfiguration>[, <delayOne>[, <delayTwo>]]]
Response(s)
CONNECT
(indicates that ME has entered data mode)
ERROR
+CME ERROR: <err>
Reference(s) PIN ASC0 ASC1 USB MUX1 MUX2 MUX3 Charge 4 Last
SIEMENS ! % % % % % % ! % %
<connectionState>
(num)
<basicConfiguration>
(num)
- AT Command Set 1
- Contents 3
- TC63 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 32
- 3. Status Control Commands 66
- 3.2 AT+CIND Indicator control 68
- 4.1 AT\Q Flow control 89
- 4.5 ATE Enable command echo 93
- 4.9.1 Autobauding 101
- 5. Security Commands 108
- 5.4 AT+CLCK Facility lock 118
- 5.5 AT^SLCK Facility lock 123
- 5.6 AT+CPWD Change Password 124
- 5.7 AT^SPWD Change Password 128
- 5.8 AT^SCSL Customer SIM Lock 130
- 6. Identification Commands 134
- 7. Call related Commands 140
- 7.2 ATA Answer a call 141
- 7.10 AT+CHUP Hang up call 151
- 7.29 ATP Select pulse dialing 178
- 7.30 ATT Select tone dialing 178
- 8. Network Service Commands 179
- 8.5 AT+CSQ Signal quality 187
- 8.6 AT^SMONC Cell Monitoring 188
- 8.7 AT^SMOND Cell Monitoring 190
- 8.8.1 AT^MONI responses 194
- 8.8.2 Service states 195
- 8.9.1 AT^MONP responses 197
- 8.10 AT^SMONG GPRS Monitor 198
- 8.12 AT^SHOM Display Homezone 202
- 9.5 AT+CCUG Closed User Group 212
- 9.7 AT+CCWA Call Waiting 218
- 10. Internet Service Commands 235
- Remote Client 257
- 11. GPRS Commands 268
- 12. FAX Commands 311
- 12.4 AT+FRM Receive Data 314
- 12.5 AT+FRS Receive Silence 315
- 12.7 AT+FTM Transmit Data 317
- 13.1 SMS parameters 319
- 13.7 AT+CMGS Send SMS message 331
- 14. SIM related Commands 363
- 15.3 Related AT Commands 384
- 16.2 ^SSTN SAT Notification 388
- 16.4 AT^SSTR SAT Response 390
- 17. Phonebook Commands 391
- 17.2 AT+CNUM Read own numbers 392
- 18. Audio Commands 411
- 18.5 AT+CMUT Mute control 414
- 18.6 AT+VTD Tone duration 415
- 19. Hardware related Commands 436
- 19.2 AT+CALA Set alarm time 437
- 19.7.4 Example: Using I²C Bus 456
- 20. Miscellaneous Commands 457
- 21. Appendix 462
Related products and manuals for Hardware Siemens TC63
Hardware Siemens BC-16 User Manual
(2 pages)
(2 pages)
Hardware Siemens 54 User Manual
(56 pages)
(56 pages)
Hardware Siemens 300 User Manual
(64 pages)
(64 pages)
Hardware Siemens CL-110-I User Manual
(129 pages)
(129 pages)
Hardware Siemens CP 1515 User Manual
(299 pages)
(299 pages)
Hardware Siemens I-SURF User Manual
(70 pages)
(70 pages)
Hardware Siemens C2-010 User Manual
(51 pages)
(51 pages)
Hardware Siemens TC35 User Manual
(39 pages)
(39 pages)
Hardware Siemens S5-135U/155U User Manual
(54 pages)
(54 pages)
Hardware Siemens TC35i User Manual
(37 pages)
(37 pages)
© 2020, manymanuals.com. All rights reserved. | 1.957 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals