Siemens TC63 User Manual Page 338
- Page / 501
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TC63 AT Command Set
13.11 AT+CNMI
s
TC63_ATC_V00.490 Page 338 of 501 5/24/05
Confidential / Draft - Do not copy
URC 5
<bm>=2 (text mode enabled):
+CBM: <sn>, <mid>, <dcs>, <page>, <pages>
<CR><LF><data>
Indicates that new cell broadcast message has been received
URC 6
<ds>=1 (PDU mode enabled):
+CDS: <length>
<CR><LF><pdu>
Indicates that new SMS status report has been received
URC 7
<ds>=1 (text mode enabled):
+CDS: <fo>, <mr>[, <ra>][, <tora>], <scts>, <dt>, <st>
Indicates that new SMS status report has been received
URC 8
<ds>=2:
+CDSI: <mem3>, <index>
Indicates that new SMS status report has been received
Command Description
The write command selects the procedure how the receipt of new SMS messages from the network is indicated
to the TE when TE is active, e.g. DTR signal is ON. If TE is inactive (e.g. DTR signal is OFF), message receiving
should be done as specified in GSM 03.38. If the DTR signal is not available or the state of the signal is ignored
(V.250 command AT&D0, reliable message transfer can be assured by using AT+CNMA acknowledgment proce-
dure. The rules <mt>=2 and <mt>=3 for storing received SM are possible only if phase 2+ compatibility is acti-
vated with AT+CSMS=1. The parameter <ds>=1 is only available in phase 2+
Parameter Description
[0]
(&F)
Buffer unsolicited result codes in the TA. If TA result code buffer is full, indica-
tions can be buffered in some other place or the oldest indications may be dis-
carded and replaced with the new received indications.
1 Discard indication and reject new received message unsolicited result codes
when TA-TE link is reserved (e.g. in on-line data mode). Otherwise forward
them directly to the TE.
2 Buffer unsolicited result codes in the TA when TA-TE link is reserved (e.g. in
on-line data mode) and flush them to the TE after reservation. Otherwise for-
ward them directly to the TE.
3 Forward unsolicited result codes directly to the TE. TA-TE link specific inband
technique used to embed result codes and data when TA is in on-line data
mode.
Rules for storing received SMS depend on the relevant data coding method (refer to GSM 03.38), preferred
memory storage (AT+CPMS) setting and this value.
Note: If AT command interface is acting as the only display device, the ME must support storage of class 0 mes-
sages and messages in the message waiting indication group (discard message)
[0]
(&F)
No SMS-DELIVER indications are routed to the TE.
1 If SMS-DELIVER is stored in ME/TA, indication of the memory location is
routed to the TE using unsolicited result code:
<mode>
(num)(&W)
<mt>
(num)(&W)(&V)
- AT Command Set 1
- Contents 3
- TC63 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 32
- 3. Status Control Commands 66
- 3.2 AT+CIND Indicator control 68
- 4.1 AT\Q Flow control 89
- 4.5 ATE Enable command echo 93
- 4.9.1 Autobauding 101
- 5. Security Commands 108
- 5.4 AT+CLCK Facility lock 118
- 5.5 AT^SLCK Facility lock 123
- 5.6 AT+CPWD Change Password 124
- 5.7 AT^SPWD Change Password 128
- 5.8 AT^SCSL Customer SIM Lock 130
- 6. Identification Commands 134
- 7. Call related Commands 140
- 7.2 ATA Answer a call 141
- 7.10 AT+CHUP Hang up call 151
- 7.29 ATP Select pulse dialing 178
- 7.30 ATT Select tone dialing 178
- 8. Network Service Commands 179
- 8.5 AT+CSQ Signal quality 187
- 8.6 AT^SMONC Cell Monitoring 188
- 8.7 AT^SMOND Cell Monitoring 190
- 8.8.1 AT^MONI responses 194
- 8.8.2 Service states 195
- 8.9.1 AT^MONP responses 197
- 8.10 AT^SMONG GPRS Monitor 198
- 8.12 AT^SHOM Display Homezone 202
- 9.5 AT+CCUG Closed User Group 212
- 9.7 AT+CCWA Call Waiting 218
- 10. Internet Service Commands 235
- Remote Client 257
- 11. GPRS Commands 268
- 12. FAX Commands 311
- 12.4 AT+FRM Receive Data 314
- 12.5 AT+FRS Receive Silence 315
- 12.7 AT+FTM Transmit Data 317
- 13.1 SMS parameters 319
- 13.7 AT+CMGS Send SMS message 331
- 14. SIM related Commands 363
- 15.3 Related AT Commands 384
- 16.2 ^SSTN SAT Notification 388
- 16.4 AT^SSTR SAT Response 390
- 17. Phonebook Commands 391
- 17.2 AT+CNUM Read own numbers 392
- 18. Audio Commands 411
- 18.5 AT+CMUT Mute control 414
- 18.6 AT+VTD Tone duration 415
- 19. Hardware related Commands 436
- 19.2 AT+CALA Set alarm time 437
- 19.7.4 Example: Using I²C Bus 456
- 20. Miscellaneous Commands 457
- 21. Appendix 462
Related products and manuals for Hardware Siemens TC63
Hardware Siemens BC-16 User Manual
(2 pages)
(2 pages)
Hardware Siemens 54 User Manual
(56 pages)
(56 pages)
Hardware Siemens 300 User Manual
(64 pages)
(64 pages)
Hardware Siemens CL-110-I User Manual
(129 pages)
(129 pages)
Hardware Siemens CP 1515 User Manual
(299 pages)
(299 pages)
Hardware Siemens I-SURF User Manual
(70 pages)
(70 pages)
Hardware Siemens C2-010 User Manual
(51 pages)
(51 pages)
Hardware Siemens TC35 User Manual
(39 pages)
(39 pages)
Hardware Siemens S5-135U/155U User Manual
(54 pages)
(54 pages)
Hardware Siemens TC35i User Manual
(37 pages)
(37 pages)
© 2020, manymanuals.com. All rights reserved. | 0.536 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals