Siemens TC63 User Manual Page 394
- Page / 501
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TC63 AT Command Set
17.3 AT+CPBR
s
TC63_ATC_V00.490 Page 394 of 501 5/24/05
Confidential / Draft - Do not copy
Type of address octet, which defines the used type of number (ton) and the numbering plan identification (npi).
Please consider that for types other than 129 or 145 dialing from phonebook with ATD><mem><n> is, depending
on the network, not always possible (refer to GSM 04.08 subclause 10.5.4.7 for details). See also <type> of
AT+CPBW.
Possible values are:
145 Dialing string <number> includes international access code character '+'
161 National number. Network support of this type is optional.
209 Dialing string <number> has been saved as ASCII string and includes non-
digit characters other than "*", "#" or "+". Note that phonebook entries saved
with this type cannot be dialed.
255 Dialing string <number> is a command to control a Supplementary Service,
i.e. "*", "#" codes are contained. Network support of this type is optional.
129 Otherwise
Text assigned to a phone number. The maximum length for this parameter is given with test command response
parameter <tlength>.
If using an ASCII terminal characters which are coded differently in ASCII and GSM have to be entered via
escape sequences as described in Section 1.5, Supported character sets.
Maximum location number for the currently selected storage. For phonebooks located on the SIM this value
depends on the SIM card type.
Maximum length of phone number for "normal" locations. Depending on the storage a limited number of loca-
tions with extended memory is available per phonebook. These locations allow storing numbers with twice the
standard length, which is 2*<nlength> digits for normal numbers, but only <nlength> digits for numbers
saved with <type>=209.
Maximum length of <text> assigned to the telephone number. The value indicated by the test command is
given in octets. If <text> is given as GSM characters each character corresponds to one octet. If the <text>
string is given in UCS2, the maximum number of characters depends on the coding scheme used for the alpha
field of the SIM according to GSM 11.11, Annex B [23]. In the worst case the number of UCS2 characters is at
least one less than half the number of GSM characters.
Note
• AT+CPBR can be used only after the phonebook data from the SIM have been read successfully for the first
time. Reading starts after successful SIM authentication has been performed, and may take up to 30 seconds
depending on the SIM used. While the initial read process is in progress, an attempt to use any of the phone-
book commands will result in "+CME Error: 14" (SIM busy).
We recommend to take advantage of the "^SSIM READY" URC. If enabled with AT^SSET, this URC notifies
the user when SIM data are accessible after SIM PIN authentication. The URC will be delivered once the ME
has completed reading data from the SIM card.
<type>
(num)
<text>
(str)(+CSCS)
<maxloc>
(num)
<nlength>
(num)
<tlength>
(num)
- AT Command Set 1
- Contents 3
- TC63 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 32
- 3. Status Control Commands 66
- 3.2 AT+CIND Indicator control 68
- 4.1 AT\Q Flow control 89
- 4.5 ATE Enable command echo 93
- 4.9.1 Autobauding 101
- 5. Security Commands 108
- 5.4 AT+CLCK Facility lock 118
- 5.5 AT^SLCK Facility lock 123
- 5.6 AT+CPWD Change Password 124
- 5.7 AT^SPWD Change Password 128
- 5.8 AT^SCSL Customer SIM Lock 130
- 6. Identification Commands 134
- 7. Call related Commands 140
- 7.2 ATA Answer a call 141
- 7.10 AT+CHUP Hang up call 151
- 7.29 ATP Select pulse dialing 178
- 7.30 ATT Select tone dialing 178
- 8. Network Service Commands 179
- 8.5 AT+CSQ Signal quality 187
- 8.6 AT^SMONC Cell Monitoring 188
- 8.7 AT^SMOND Cell Monitoring 190
- 8.8.1 AT^MONI responses 194
- 8.8.2 Service states 195
- 8.9.1 AT^MONP responses 197
- 8.10 AT^SMONG GPRS Monitor 198
- 8.12 AT^SHOM Display Homezone 202
- 9.5 AT+CCUG Closed User Group 212
- 9.7 AT+CCWA Call Waiting 218
- 10. Internet Service Commands 235
- Remote Client 257
- 11. GPRS Commands 268
- 12. FAX Commands 311
- 12.4 AT+FRM Receive Data 314
- 12.5 AT+FRS Receive Silence 315
- 12.7 AT+FTM Transmit Data 317
- 13.1 SMS parameters 319
- 13.7 AT+CMGS Send SMS message 331
- 14. SIM related Commands 363
- 15.3 Related AT Commands 384
- 16.2 ^SSTN SAT Notification 388
- 16.4 AT^SSTR SAT Response 390
- 17. Phonebook Commands 391
- 17.2 AT+CNUM Read own numbers 392
- 18. Audio Commands 411
- 18.5 AT+CMUT Mute control 414
- 18.6 AT+VTD Tone duration 415
- 19. Hardware related Commands 436
- 19.2 AT+CALA Set alarm time 437
- 19.7.4 Example: Using I²C Bus 456
- 20. Miscellaneous Commands 457
- 21. Appendix 462
Related products and manuals for Hardware Siemens TC63
Hardware Siemens BC-16 User Manual
(2 pages)
(2 pages)
Hardware Siemens 54 User Manual
(56 pages)
(56 pages)
Hardware Siemens 300 User Manual
(64 pages)
(64 pages)
Hardware Siemens CL-110-I User Manual
(129 pages)
(129 pages)
Hardware Siemens CP 1515 User Manual
(299 pages)
(299 pages)
Hardware Siemens I-SURF User Manual
(70 pages)
(70 pages)
Hardware Siemens C2-010 User Manual
(51 pages)
(51 pages)
Hardware Siemens TC35 User Manual
(39 pages)
(39 pages)
Hardware Siemens S5-135U/155U User Manual
(54 pages)
(54 pages)
Hardware Siemens TC35i User Manual
(37 pages)
(37 pages)
© 2020, manymanuals.com. All rights reserved. | 0.504 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals