Siemens TC63 User Manual Page 239
- Page / 501
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TC63 AT Command Set
10.1 AT^SICS
s
TC63_ATC_V00.490 Page 239 of 501 5/24/05
Confidential / Draft - Do not copy
uses dynamic DNS assignment. Any other address means that the Primary
DNS is manually set.
The default value applies automatically if no other address is set. Note that the
AT^SICS read command only returns a manually configured IP address, while
the value "0.0.0.0" is not indicated at all, no matter whether assumed by default
or explicitly specified.
“dns2“ Secondary DNS server address (IP address in dotted-four-byte format).
If "dns1" = "0.0.0.0" this setting will be ignored. Otherwise this value can be
used to manually configure an alternate server for the DNS1.
If "dns1" is not equal "0.0.0.0" and no "dns2" address is given, then
"dns2"="0.0.0.0" will be assumed automatically. The AT^SICS read command
only returns a manually configured IP address, while the value "0.0.0.0" is not
indicated at all, no matter whether assumed by default or explicitly specified.
Parameter value; type and supported content depend on related <conParmTag>.
Supported connection type values in <conParmValue> for <conParmTag> value "conType".
“CSD“ Circuit-switched data call.
“GPRS0“ GPRS connection.
Settings of GPRS related commands are not used, e.g. AT+CGDCONT. When a
service based on a GPRS connection profile is started after entering AT^SISO
TC63 automatically tries to attach to the GPRS. Yet, the only exception is
AT+CGATT which can be used any time to detach from the GPRS and, and thus
disconnect the bearer opened with AT^SISO.
“none“ Clears the connection profile.
Character set selectable with <conParmValue> for <conParmTag> value "alphabet".
[“0“] Character set determined with AT+CSCS applies.
“1“ International Reference Alphabet (IRA, seven bit ASCII) applies.
Supported data rate values in <conParmValue> for <conParmTag> value "dataRate".
“0“ 14.4 KBaud
[“1“] 9.6 KBaud
Supported data call type values in <conParmValue> for <conParmTag> value "dataType".
“0“ ISDN
[“1“] Analog
<conParmValue>
(str)
<conParmValue-conType>
(str)
<conParmValue-alphabet>
(str)
<conParmValue-dataRate>
(str)
<conParmValue-dataType>
(str)
- AT Command Set 1
- Contents 3
- TC63 AT Command Set 10
- List of Tables 12
- List of Figures 13
- 1. Introduction 14
- 1.2 Related documents 15
- 1.3 Document conventions 16
- 1.3.1 Quick reference table 16
- 1.4 AT Command Syntax 18
- 1.4.1 Using Parameters 18
- 1.5 Supported character sets 20
- 1.9 Errors and Messages 29
- 2. Configuration Commands 30
- 2.2.1 AT&V responses 32
- 3. Status Control Commands 66
- 3.2 AT+CIND Indicator control 68
- 4.1 AT\Q Flow control 89
- 4.5 ATE Enable command echo 93
- 4.9.1 Autobauding 101
- 5. Security Commands 108
- 5.4 AT+CLCK Facility lock 118
- 5.5 AT^SLCK Facility lock 123
- 5.6 AT+CPWD Change Password 124
- 5.7 AT^SPWD Change Password 128
- 5.8 AT^SCSL Customer SIM Lock 130
- 6. Identification Commands 134
- 7. Call related Commands 140
- 7.2 ATA Answer a call 141
- 7.10 AT+CHUP Hang up call 151
- 7.29 ATP Select pulse dialing 178
- 7.30 ATT Select tone dialing 178
- 8. Network Service Commands 179
- 8.5 AT+CSQ Signal quality 187
- 8.6 AT^SMONC Cell Monitoring 188
- 8.7 AT^SMOND Cell Monitoring 190
- 8.8.1 AT^MONI responses 194
- 8.8.2 Service states 195
- 8.9.1 AT^MONP responses 197
- 8.10 AT^SMONG GPRS Monitor 198
- 8.12 AT^SHOM Display Homezone 202
- 9.5 AT+CCUG Closed User Group 212
- 9.7 AT+CCWA Call Waiting 218
- 10. Internet Service Commands 235
- Remote Client 257
- 11. GPRS Commands 268
- 12. FAX Commands 311
- 12.4 AT+FRM Receive Data 314
- 12.5 AT+FRS Receive Silence 315
- 12.7 AT+FTM Transmit Data 317
- 13.1 SMS parameters 319
- 13.7 AT+CMGS Send SMS message 331
- 14. SIM related Commands 363
- 15.3 Related AT Commands 384
- 16.2 ^SSTN SAT Notification 388
- 16.4 AT^SSTR SAT Response 390
- 17. Phonebook Commands 391
- 17.2 AT+CNUM Read own numbers 392
- 18. Audio Commands 411
- 18.5 AT+CMUT Mute control 414
- 18.6 AT+VTD Tone duration 415
- 19. Hardware related Commands 436
- 19.2 AT+CALA Set alarm time 437
- 19.7.4 Example: Using I²C Bus 456
- 20. Miscellaneous Commands 457
- 21. Appendix 462
Related products and manuals for Hardware Siemens TC63
Hardware Siemens BC-16 User Manual
(2 pages)
(2 pages)
Hardware Siemens 54 User Manual
(56 pages)
(56 pages)
Hardware Siemens 300 User Manual
(64 pages)
(64 pages)
Hardware Siemens CL-110-I User Manual
(129 pages)
(129 pages)
Hardware Siemens CP 1515 User Manual
(299 pages)
(299 pages)
Hardware Siemens I-SURF User Manual
(70 pages)
(70 pages)
Hardware Siemens C2-010 User Manual
(51 pages)
(51 pages)
Hardware Siemens TC35 User Manual
(39 pages)
(39 pages)
Hardware Siemens S5-135U/155U User Manual
(54 pages)
(54 pages)
Hardware Siemens TC35i User Manual
(37 pages)
(37 pages)
© 2020, manymanuals.com. All rights reserved. | 0.418 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals