Siemens IC60 User Manual Page 39
- Page / 172
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Voice board IAV6-90
39
Building Technologies
Fire Safety & Security Products
6.3.2.2 Call-back
In order to activate this mode, option 5 at P183E must be OFF and option 8 at P175E 2E must be ON.
Dialer B options
P175E 2E 8
After reporting the event to the CMS the Control Panel rings off.
When this option is turned on, the Control Panel will ring off after reporting to the
CMS. The operator at CMS can then call the Control Panel during a period
10 minutes. The panel will answer the incoming call on the first ring.
If the DTMF code defined by parameter P175E 14E (as described above) is not
entered within 30 seconds, the panel will ring off. The panel will still answer any
new calls on the first ring within the 10 minutes after the original alarm was
transmitted. As soon as the panel receives the correct DTMF acknowledge code
the auto-answer feature (answering on the 1st ring) will be reset.
After the Control Panel has answered an incoming call, a short beep will sound at intervals of
5 seconds for a period of 30 seconds. If nothing happens and the 30 seconds timer expires, the panel
will ring off. If however the DTMF code programmed by parameter P175E 14E is entered before the
30 seconds timer has expired (for example if a code "1234" was programmed by parameter
P175E 14E, then the operator must enter 1-2-3-4-# at their telephone), the call will be extended. The
short beeps will stop and the two-way voice channel will remain open for 3 minutes (if no code has
been programmed at P175E 14E, the call can be extended by pressing the # button). After 2 minutes
and 30 seconds the short beeps will start again. The operator must repeat the above process to keep
the panel on-line for a further 3 minutes, otherwise the panel will ring off when the 3 minutes are over.
If the operator wishes to terminate the two-way voice connection, he should enter
0-0-0-# on his telephone which will tell the panel to ring off.
6.3.3 Additional commands available for Voice Board
6.3.3.1 Output DTMF
Output DTMF
P175E 12E 0-9999E
(Value 1-4 digit code 0-9999)
The panel can be configured to allow remote operation of the outputs via a remote
telephone. The code programmed at this address is the DTMF code that must be
used when performing this function. When dialing the panel and it has answered
the call, after waiting for the panel modem tones to stop you can enter in the 4 digit
DTMF code plus the output number you wish to control, e.g. 1 for output # 1, and
the current status will be given of the output associated with the code entered.
After that, if you press the <*> button on the telephone the status of the output will
toggle e.g. if it was previously on it will change to off or vice versa. When finished
you simply hang-up and 15 seconds later the panel will release the line.
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Related products and manuals for Security access control systems Siemens IC60
(50 pages)
(184 pages)© 2020, manymanuals.com. All rights reserved. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals