Siemens IC60 User Manual Page 18
- Page / 172
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
System overview
18
Building Technologies
Fire Safety & Security Products
4 System overview
4.1 Sintony 60M modular
Outputs
Gnd Gnd
Gnd
Gnd12V 12V
12V
12V
1152263374CCCC48Tmp
AC_IN
C NC N
Relay/OUT4
COM
GND
IC-60M
In factory settings the
jumper is set between
COM & GND.
The com contact can be
connected to 12V by
setting the jumper.
With out the jumper the
relay contacts are floating.
Red
Black
OUTPUTS
INPUTS Z1...Z16 POWER FOR
DETECTORS &
A
CCESORIES
Out
TELECOM
LinIn
Dat
Lin
Clk
Neg
Pos
PHONE LINE IN
PHONE LINE IN
PHONE LINE OUT
BUS CONNECTION
FOR EXTERNAL
KEYPAD AND OTHER
ACCESSORIES
Fig. 1 Connection Diagram
The wiring option shown here with a common tamper input (TAMP/GND) is not
allowed in all countries, if the installation has to be done according to legal
requirements (e.g. Belgium/INCERT).To integrate the tamper contact directly into
each zone input, see also chapter
4.3.2: Zone wiring examples.
Battery Specifications for Model IC60 M
z Sealed Lead-Acid Rechargeable Battery 12 V/1.3 Ah up to 12 V/7 Ah
z Battery cutoff level (when AC mains fails): 10.3 V ± 0.1 V DC.
z Full charge after 48 hours.
z The current limit over charge is 600 mA.
Battery Connections
Connect a sealed lead acid rechargeable 12 V DC battery to the terminals labeled
red and black on the control panel being careful to observe the correct polarity. The
maximum recommended battery capacity is 7 amp hours. Battery charge current at
these terminals is limited to 600 mA maximum. The battery connection is protected
against short circuits by a thermal fuse (F1). The panel performs a dynamic load
test on the battery every 15 seconds and if it fails the test at any time it will flash
the battery LED.
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Related products and manuals for Security access control systems Siemens IC60
(50 pages)
(184 pages)© 2020, manymanuals.com. All rights reserved. | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals