Siemens IC60 User Manual Page 16
- Page / 172
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Programming to EN 50131
16
Building Technologies
Fire Safety & Security Products
P25E 13E Option 8:
Limit Events & Dialer to 3 of any one type
refer to chapter
14.3: Miscellaneous user options
Option 8:
Limit Events & Dialer to 3 of any one Type: if this option is turned on the panel will
not record any more than 3 events in memory for any event type during a single
arm or disarm cycle, e.g. if the AC failed 4 times while armed or disarmed the
panel will only record the AC fail 3 times in memory and will only report the AC fail
3 times to the dialer. As soon as the arm state has changed any count are reset
back to zero again. If this option is off there is no limit on the recording and
reporting of events.
According EN 50131-3 the events of the same type should be limited to 3.
P36E Option 5:
Output Disabled when P25E3E timer is running
refer to chapter
16.1: Output options
Option 5:
Output Disabled when P25E 3E timer is running: this option will cause the output to
be disabled when the dialer reporting delay is active. It is designed to keep external
audible alarms silent when the dial delay is active (allowing internal alarms to warn
that the alarm will be reported to monitoring if not unset) but if the alarm hasn’t
been reset before the timer expires the external alarm will sound.
According EN 50131-3 if an alarm occurred during Exit Delay the dialer
should reported only after 30sec.
And the Siren shouldn't activate until the Exit delay is expired.
P37E Option 4:
Disable outputs during two way voice mode
refer to chapter
16.1: Output options
Option 4:
Turn Output OFF during Two Way Voice Mode: if the panel has a full duplex two
way voice board fitted and the settings at P175E 2E option 8 and P183E option 5
are set to allow full duplex mode, any outputs with this option turned on will be
disabled while two way voice is operational. This is to ensure that local sirens do
not interfere with the two way voice audio signal.
According EN 50131-3 if an alarm occurred during Exit Delay the dialer
should reported only after 30sec.
And the Siren shouldn't activate until the Exit delay is expired.
P46E Option 7:
Cannot Arm if Zone unsealed at end of Exit Delay
refer to chapter
17.1: Area arm and special function options
Option 7:
Cannot Arm if Zone unsealed at end of Exit Delay: if this option is turned on and a
zone becomes unsealed as the exit delay expires the panel will fail to arm and
report this via the dialer. The unsealed zone must be corrected and the system re-
armed again.
According EN 50131-3 the system shouldn't Arm if one of the zones is open
at the end of Exit Delay.
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Related products and manuals for Security access control systems Siemens IC60
(50 pages)
(184 pages)© 2020, manymanuals.com. All rights reserved. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals