Siemens SIMATIC IPC427C Operations Instructions Page 44
- Page / 182
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Commissioning
7.2 Commissioning - Windows Embedded Standard
SIMATIC IPC427C
44 Operating Instructions, 10/2010, A5E02414743-03
7.2 Commissioning - Windows Embedded Standard
7.2.1 Basic commissioning - initial startup
Requirements
● The device is connected to the 24 VDC power supply.
● The equipotential bonding lines are wired.
● The connecting cables are properly inserted.
Setting up the operating system
After initial power up, the Windows Embedded Standard operating system that is pre-
installed on the CompactFlash card, SSD, or hard disk is set up automatically on the
computer.
Proceed as follows:
1. Switch on the device using the On/Off switch. The device performs a power on self-test.
During the self-test, this message appears:
Press F2 go to Setup Utility or
Press ESC go to Boot Manager
2. Wait until this message is cleared, then follow the instructions on the screen.
NOTICE
The device may not be switched off at any time during the installation process.
Do not change the defaults in BIOS Setup, otherwise the operating system setup may
become corrupted.
3. Restart
After you have entered all the necessary information and the operating system is
configured,
you are prompted to restart the system. Respond to this prompt with Yes.
Note
Initial commissioning of Windows Embedded Standard 2009
System startup can take considerably longer than usual during initial commissioning of
Windows Embedded Standard 2009. Only a blue or black screen is displayed for several
minutes.
- SIMATIC IPC427C 1
- SIMATIC 1
- Industrial PC 1
- SIMATIC IPC427C 1
- Table of contents 3
- Table of contents 5
- Introduction 9
- History 10
- Safety Instructions 11
- Battery 12
- ESD directives 12
- Description 13
- 3.3 Features 14
- Description 15
- 3.3 Features 15
- 3.6 Design 19
- Ports and power supply 20
- 3.6 Design 21
- 3.6.3 Operator controls 22
- 3.6.4 Status displays 23
- 3.6 Design 24
- Application planning 25
- Examples for COA-Labels 26
- Application planning 27
- Installing/mounting 29
- 5.2 Mounting information 31
- 5.3 Mounting the device 31
- 5.4 Mounting on DIN rails 31
- 5.4 Mounting on DIN rails 32
- Installing/mounting 33
- 5.6 Upright mounting 35
- 5.6 Upright mounting 36
- Connecting 37
- Connecting 39
- 6.4 USB strain-relief 40
- 6.5 PROFINET strain relief 41
- 6.5 PROFINET strain relief 42
- Commissioning 43
- Requirements 44
- Switch off the device 45
- Change system language 46
- Ultimate 49
- 7.5.1 Commissioning - guide 50
- 8.1 Overview 51
- 8.2 PROFINET 52
- 8.2 PROFINET 53
- 8.2 PROFINET 54
- Functions 55
- 9.1.3 Watchdog (WD) 56
- WD monitoring times 57
- Purpose and function 57
- Set EWF 57
- Configuring FBWF 59
- 9.4 HAL tool 60
- 9.5 SRAM buffer memory 61
- 9.6 Battery monitoring 61
- Preparation 63
- Open the device 63
- 10.2 Memory expansion 64
- Installing a memory module 65
- 10.3.1 Notes on the modules 66
- Mounting PCI-104 or PC/104 67
- modules 67
- ② and secure it 68
- Memory expansion options 69
- ① of the module 70
- ① and remove 72
- Maintenance and Service 75
- Removing drives 76
- Installing a drive 77
- Disposal 78
- Replacing the battery 79
- Reconfiguring the BIOS Setup 79
- Restoring the factory state 80
- Maintenance and Service 81
- Partition setup 83
- Partitioning the hard disk 88
- Partitioning the SSD 88
- Reduce partition 92
- Increase partition 92
- 11.5 Installing updates 94
- 11.6 Data backup 95
- 11.7 CP 1616 onboard 95
- 11.7 CP 1616 onboard 96
- 12.1 Boot error messages 97
- 12.1 Boot error messages 98
- Troubleshooting/FAQs 100
- Technical specifications 101
- 14.1 General specifications 102
- Technical specifications 103
- Dimension drawings 107
- Dimension drawings 109
- Detailed descriptions 115
- 16.1.3 External ports 116
- 16.1.3.2 COM1/2 117
- 16.1.3.3 DVI-I 117
- /(' /(' 118
- 16.1.3.5 USB 119
- 16.1.3.6 PROFIBUS 119
- 16.1.4 Internal ports 121
- 16.1 Internal components 122
- 16.2 BIOS Setup 123
- 16.2.2 Starting BIOS Setup 124
- Menu layout 125
- 16.2.4 Main menu 126
- System time and date 127
- 16.2 BIOS Setup 128
- Detailed descriptions 129
- 16.2 BIOS Setup 129
- 16.2.5 Advanced Menu 132
- 16.2.6 Security menu 135
- 16.2.7 Boot menu 136
- 16.2.8 Version menu 139
- 16.2.9 Exit Menu 140
- BIOS Setup default settings 141
- 16.3 System resources 143
- 16.3 System resources 144
- 16.4 I/O Address Areas 145
- Watchdog trigger register 146
- Meaning of the bits 147
- 16.5.1 Introduction 149
- CP 1616 onboard as IO device 150
- 16.5.2 Firmware Loader 151
- Configuring 153
- Appendix 155
- DIN ISO 9001 certificate 156
- Software License Agreement 156
- A.3 Service and support 157
- A.3 Service and support 158
- ESD guidelines 159
- B.1 ESD Guidelines 160
- List of abbreviations 161
- C.1 Abbreviations 162
- List of abbreviations 163
- C.1 Abbreviations 163
- Glossary 167
- Glossary 169
- SIMATIC IPC427C 180
- Index 181
© 2020, manymanuals.com. All rights reserved. | 0.478 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals