Siemens Sinumerik 810T User Manual download pdf (Page 78)

EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES

H 2

0037 Memory allocation failure

Remedy: Close all other WINDOWS applications or

restart WINDOWS.

0038 Unauthorized software version

Contact EMCO.

0039 Project data non compatible to software

version

Possible error after updates, contact EMCO.

0040 Invalid entry for DNC interface in the

profile ...

Cause: The DNC entry in the file project.ini is

invalid.

Remedy: Setting with WinConfig

0100 Mailslot could not be created

Cause: Insufficient memory in the memory area

below 640 kB.

Remedy: Close all other applications, restart

WINDOWS. If this is not successfull,

remove not necessary device and drivers

entries in config.sys or load them in the

upper memory area.

0101 For WinCTS Windows for Workgroups

3.11 or higher is required

WinCTS requires WINDOWS for WORKGROUPS

version 3.11 or higher.

0102 Error creating the reference table for

keybitmaps

Remedy: Restart WINDOWS. If this alarm occurs

repeatedly, contact EMCO.

0103 Invalid entry for WinCTS status in the

profile ...

Cause: The CTS entry in the file project.ini is

invalid.

Remedy: Contact EMCO

0104 Error getting the workgroup name

Remedy: Restart WINDOWS. If this alarm occurs

repeatedly, contact EMCO.

0105 No workgroup found

Remedy: Insert the computer into the workgroup for

WinCTS, if necessary set up a workgroup

for the WinCTS computers.

0106 Invalid entry for the number of keys to

record in the profile ...

Cause: The KeyFifoSize entry in the file winnc.ini

is invalid.

Remedy: Correct the number, e.g. 50(see

WinConfig).

0107 - 0110 (various alarms)

Remedy: Restart WINDOWS. If this alarm occurs

repeatedly, contact EMCO.

Control Alarms

These alarms can occur only with operating and

programming the control functions or with running

CNC programs.

16 Parity error (RS232)

Cause: data I/O: data transmition error character

overflow

Remedy: set same parity for sender and receiver

17 Overflow error (RS232)

Cause: data I/O: data transmition error parity

18 Frame error (RS232)

Cause: data I/O: data transmition error data frame

Remedy: ev. set same configuration for both RS232

30 PP memory overflow (RS232)

Cause: data I/O: unknown data type, error data

32 Data format error (RS232)

Cause: data I/O: error while opening file

1040 ORDxx DAC limit X

Cause: step motor in X felt out of pace

Remedy: e.g. select lower feed or chip cross section,

check slides for smooth running, approach

reference point

1041 ORDxx DAC limit Y

see alarm 1040

1042 ORDxx DAC limit Z

see alarm 1040

1480 ORDxx SW overtravel switch X

Cause: software end switch in X overtravelled

Remedy: traverse back manually

1481 ORDxx SW overtravel switch Y

see alarm 1480

1482 ORDxx SW overtravel switch Z

see alarm 1480

1560 Nxxxx Set speed to high/low

Cause: too high/low S-value

Remedy: correct program, enter belt gage in setting

data

2040 Block not in memory

Cause: Block search target not found

Remedy: correct program

2041 CNC program not foand

Cause: NC Program (subroutine, contour routine)

not found; with NC start no program was

selected

Remedy: correct call up or create program

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 89 90

Comments to this Manuals

No comments

Siemens Sinumerik 810T User Manual Page 78

Comments to this Manuals

Related products and manuals for Networking Siemens Sinumerik 810T