Siemens Sinumerik 810T User Manual Page 21
- Page / 90
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
EMCO WINNC SINUMERIK 810/820 T
C 1
OPERATING SEQUENCES
C: Operating Sequences
Survey Modes
AUTOMATIC
For working off a part program the control calls up
block after block and interprets them.
The interpretation considers all corrections which are
called up by the program.
The so-handled blocks will be worked off one by one.
JOG
With the JOG keys the tool can be traversed manually.
In the submode OVERSTORE (softkey) you can
switch on the spindle and swivel the tool turret.
MDI-AUTOMATIC
You can enter blocks of a part program in the
intermediate store.
The control works off the inserted blocks and deletes
the intermediate store for new entries.
REFPOINT
This mode is used to approach the reference point.
With reaching the reference point the actual position
store is set to the value of the reference point
coordinates. By that the control acknowledges the
position of the tool in the working area.
With the following situations the reference point has
to be approached:
• After switching on the machine
• After mains interruption
• After alarm "Approach reference point" or "Ref.
point not reached".
• After collisions or if the slides stucked because of
overload.
I 1 ... I 10 000
10000
1
...
In this mode the slides can be traversed for the
desired increment (1...10000 in µm/10
-4
inch) with
means of the JOG keys
-X
+ X
-Z
+Z
.
The selected increment (1, 10, 100, ...) must be
larger than the machine resolution (smallest possible
traverse path), otherwise no movement will occur.
- Software Description 1
- Contents 3
- E: @-Codes 4
- G: Survey Pages 4
- H: Alarms and Messages 4
- Starting Information 4
- A: Key Description 5
- Key functions 6
- Address and Numeric Keyboard 6
- Machine Control Keys 8
- KEY DESCRIPTION 9
- PC Keyboard 10
- Screen with Softkeys 11
- INNC SINUMERIK 810/820 T 12
- EY DESCRIPTION 12
- B: Basics 13
- Zero Offset 14
- Coordinate System 14
- Input of the 15
- Tool Data Measuring 16
- Cutter position 17
- Input of the Tool Data 18
- Tool Data Measuring with the 20
- Optical Presetting Device 20
- C: Operating Sequences 21
- Approach the Reference Point 22
- Input of the Gear Position 22
- Setting of Language and 22
- Workpiece directory 22
- Input of Programs 23
- PERATING SEQUENCES 24
- Program Administration 25
- Data Input-Output 25
- Program Run 29
- Graphic simulation 31
- D: Programming 33
- Survey of G Commands 34
- Survey of M Commands 34
- Survey of Cycles 34
- Description of G Commands 35
- G01 Linear Interpolation 35
- G02 Circular Interpolation 36
- Clockwise 36
- G03 Circular Interpolation 36
- Counterclockwise 36
- G04 Dwell 37
- G09 Exact Stop 37
- G10 - G13 Polar Coordinate 37
- Interpolation 37
- G25/G26 Programmable working 38
- G33 Thread Cutting 39
- Cutter Radius Compensation 39
- ROGRAMMING 40
- G48 Leave as Approached 42
- G50 Cancel Scale Modification 42
- G51 Scale Modification 42
- G54 - G57 Zero Offset 1 - 4 43
- G58/G59 Programmable Zero 43
- G60 Exact Stop Mode 44
- G63 Thread tapping with 44
- G70 Measuring in Inches 45
- G71 Measuring in Millimetre 45
- G92 Spindle Speed Limit 46
- G90 Absolute Programming 46
- G91Incremental Programming 46
- G94 Feed per Minute 49
- G95 Feed per Revolution 49
- G96 Constant Cutting Speed 49
- G97 Constant Spindle Speed 49
- G131 Transmit 50
- Description of Cycles 55
- L93 Cut-in Cycle 55
- L94 Undercut Cycle 56
- L97 Thread Cutting Cycle 58
- L971 Longitudinal Thread 58
- L98 Deep Hole Drilling Cycle 59
- L99 Thread Draft 60
- Contour definition 61
- Subroutines 63
- R PARAMETER 71
- OFFSET" 73
- Softkey Menu Survey 74
- Survey Guiding 76
- Control Alarms 78
- Machine Alarms 85
Related products and manuals for Networking Siemens Sinumerik 810T
Networking Siemens 505-2571 Specifications
(68 pages)
(68 pages)
Networking Siemens DTU3005-B Operator's Manual
(141 pages)
(141 pages)
Networking Siemens MC35 Specifications
(42 pages)
(42 pages)
Networking Siemens TC35 Terminal Specifications
(204 pages)
(204 pages)
Networking Siemens TC35 Terminal Specifications
(278 pages)
(278 pages)
Networking Siemens RS-485 Service Manual
(92 pages)
(92 pages)
Networking Siemens gigaset SE551 User Manual
(183 pages)
(183 pages)
Networking Siemens SE505 Specifications
(135 pages)
(135 pages)
Networking Siemens RS-485 Service Manual
(46 pages)
(46 pages)
Networking Siemens S7-200PLC User Manual
(21 pages)
(21 pages)
Networking Siemens DTU3005-B Operator's Manual
(120 pages)
(120 pages)
Networking Siemens 505-2571 User Manual
(30 pages)
(30 pages)
Networking Siemens E-110-I User Manual
(10 pages)
(10 pages)
Networking Siemens SIMATIC TIWAY 1 User Manual
(118 pages)
(118 pages)
Networking Siemens SL2-141 User Manual
(20 pages)
(20 pages)
© 2020, manymanuals.com. All rights reserved. | 1.456 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals