Siemens Sinumerik 810T User Manual download pdf (Page 17)

EMCO WINNC SINUMERIK 810/820 T

B 5

BASICS

With "wear" occurs the correction of not exact

measured tool data or worn tools after several

machining runs. The inserted length corrections will

be added to or subtracted from the geometry of the

tool incrementally.

X+/- .....incremental in diameter

Z+/-......incremental

R+/- .....incremental

Cutter position

Cutter position (Type)

Look at the tool like it is clamped at the machine to

determine the tool type.

For machines with the tool below (in front of) the

turning centre (e.g. PC TURN 50/55) the values in

brackets must be used because of the opposite +X

direction of these machines.













 



1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 89 90

Software Description 1
Contents 3
E: @-Codes 4
G: Survey Pages 4
H: Alarms and Messages 4
Starting Information 4
A: Key Description 5
Key functions 6
Address and Numeric Keyboard 6
Machine Control Keys 8
KEY DESCRIPTION 9
PC Keyboard 10
Screen with Softkeys 11
INNC SINUMERIK 810/820 T 12
EY DESCRIPTION 12
B: Basics 13
Zero Offset 14
Coordinate System 14
Input of the 15
Tool Data Measuring 16
Cutter position 17
Input of the Tool Data 18
Tool Data Measuring with the 20
Optical Presetting Device 20
C: Operating Sequences 21
Approach the Reference Point 22
Input of the Gear Position 22
Setting of Language and 22
Workpiece directory 22
Input of Programs 23
PERATING SEQUENCES 24
Program Administration 25
Data Input-Output 25
Program Run 29
Graphic simulation 31
D: Programming 33
Survey of G Commands 34
Survey of M Commands 34
Survey of Cycles 34
Description of G Commands 35
G01 Linear Interpolation 35
G02 Circular Interpolation 36
Clockwise 36
G03 Circular Interpolation 36
Counterclockwise 36
G04 Dwell 37
G09 Exact Stop 37
G10 - G13 Polar Coordinate 37
Interpolation 37
G25/G26 Programmable working 38
G33 Thread Cutting 39
Cutter Radius Compensation 39
ROGRAMMING 40
G48 Leave as Approached 42
G50 Cancel Scale Modification 42
G51 Scale Modification 42
G54 - G57 Zero Offset 1 - 4 43
G58/G59 Programmable Zero 43
G60 Exact Stop Mode 44
G63 Thread tapping with 44
G70 Measuring in Inches 45
G71 Measuring in Millimetre 45
G92 Spindle Speed Limit 46
G90 Absolute Programming 46
G91Incremental Programming 46
G94 Feed per Minute 49
G95 Feed per Revolution 49
G96 Constant Cutting Speed 49
G97 Constant Spindle Speed 49
G131 Transmit 50
Description of Cycles 55
L93 Cut-in Cycle 55
L94 Undercut Cycle 56
L97 Thread Cutting Cycle 58
L971 Longitudinal Thread 58
L98 Deep Hole Drilling Cycle 59
L99 Thread Draft 60
Contour definition 61
Subroutines 63
R PARAMETER 71
OFFSET" 73
Softkey Menu Survey 74
Survey Guiding 76
Control Alarms 78
Machine Alarms 85

Comments to this Manuals

No comments

Siemens Sinumerik 810T User Manual Page 17

Comments to this Manuals

Related products and manuals for Networking Siemens Sinumerik 810T