Siemens OSM User Manual Page 23
- Page / 158
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Important OSM/ESM Functions
2-3
Industrial Ethernet OSM/ESM Network Management
C79000-G8976-C137-08
2.2 Autocrossover
Electrical OSM/ESM ports with the autocrossover function are capable of crossing
over the send and receive signals internally in the port. This means that
straight-through or crossover TP cables can be used without causing problems.
To use the autocrossover function:
S At least one of the two ports must support the autocrossover function.
S The autonegotiation mode must be set on the port providing the autocrossover
function.
OSM TP22, ESM TP40 and all OSMs/ESMs with order numbers ending in “10” (for
example, 6GK1105-2AA10) provide autocrossover functionality.
Notice
Please note that even when using straight-through cables, an invalid loop can re-
sult in the Ethernet network, for example, by linking two ports on one OSM/ESM.
Such a loop can lead to network overload and network failures.
2.3 Transmission Rate and Duplicity
The transmission rate and/or duplicity of the electrical ports can also be set by the
user with network management functions. The values are shown in Table 2-1
below.
The transmission rate and duplicity of a port set by the user only comes into effect
if autonegotiation is turned off for the port.
Table 2-1 Transmission Rate and Duplicity
Ports Transmission
Rate
Duplicity
Electrical ports 10 or 100 Mbps Half duplex or full duplex
Optical ports only 100 Mbps Only full duplex
- Purpose of the Manual 6
- Scope of the Manual 6
- Notes for the Reader 7
- Finding Information 7
- Target Group 7
- Audience 8
- Further Support 9
- C79000-G8976-C137-08 10
- Introduction 13
- 1.1.1 Function 14
- Protocol 15
- Getting Information 15
- Making Settings 15
- 1.2.1 Signaling Concept 17
- 1.2.2 Network Management 17
- 1.3 Command Interpreter (CLI) 20
- 1.4 Setting the IP Addresses 20
- Important OSM/ESM Functions 21
- 2.1 Autonegotiation 22
- 2.2 Autocrossover 23
- Defaults 24
- Protected Settings 24
- Restore Factory Defaults 24
- 2.6 Locked Ports 28
- 2.7 Mirroring 29
- 2.8 Traps 30
- 2.9 E-Mail Function 31
- 2.10 Event Log Table 32
- 2.12 Flow Control 34
- 2.13 BOOTP/DHCP 35
- 2.15 TELNET 37
- Redundant Coupling 38
- 1 Fiber-optic cable (FO) 39
- 2 ITP XP standard cable 9/9 39
- 2.17 Observer Function 41
- Command Interpreter (CLI) 44
- 3.1 Overview 45
- 3.2 Password Protection 45
- 3.3 Installing the CLI 46
- 3.4 Login 47
- 3.5 CLI Commands 48
- CLI Menus and Description 49
- Start Menu 50
- System Menu 51
- Command CommentDescription 52
- OSM/ESM Menu 53
- Agent Menu 55
- Switch Menu 58
- Port Menu 60
- Service Menu 61
- Web-Based Management (WBM) 62
- 4.1 General Introduction 63
- 4.2 Requirements 64
- 4.3 Connecting 65
- Figure 4-2 “Login” Window 66
- Figure 4-3 WBM Startup Window 67
- Device Status Field 69
- Menu Tree 69
- Data Window 69
- 4.6 Management Menus 70
- 4.7 System 71
- 4.7.1 System Version Numbers 72
- Hardware 73
- Order Number 73
- Boot software 73
- Operative software 73
- MAC Address 73
- 4.7.2 System Restart 74
- 4.7.3 System Factory Defaults 75
- (restoring the defaults) 75
- 4.7.4 System Save & Load 76
- Log Table File 77
- Firmware File 77
- 4.7.5 Event Log Table 78
- 4.8 OSM/ESM Status 79
- Standby Status 80
- RM Status 80
- Power Line 1 80
- Power Line 2 80
- Fault Status 81
- 4.8.1 OSM/ESM Fault Mask 82
- Set New Values 83
- 4.8.2 OSM/ESM Standby Mask 84
- 4.8.3 OSM/ESM Counters 86
- 4.9 Agent Features 88
- E-Mail Address 92
- SMTP Server IP Address 92
- “From” Field 93
- 4.9.5 Agent ARP Table 95
- 4.9.6 Agent SNMP Counters 96
- 4.10 Switch Features 97
- Flow Control 98
- Set New Value 98
- 4.10.1 Current FDB Table 99
- Start with MAC 100
- Clear Address 100
- Next Values 100
- 4.10.2 Static FDB Table 101
- Entering a Multicast Address 105
- 4.11 Port Status 106
- Flow Ctrl 107
- 4.11.1 Port Configuration 108
- 4.12 Statistics Counters 110
- 4.12.1 Packet Size 111
- 4.12.2 Packet Type 112
- 4.12.3 Packet Error 113
- SNMP and RMON 114
- 5.1 SNMP 115
- 5.2 RMON 116
- 6.1 General Introduction 118
- Figure 6-1 119
- Figure 6-2 120
- Figure 6-3 120
- Figure 6-4 121
- Requirements 122
- Notes on Troubleshooting 124
- Internet Browser Settings 128
- Figure A-2 Trusted Sites 130
- A.2 Netscape Communicator 6.2 138
- Serial Port of the OSM/ESM 140
- Figure B-1 Properties Tab 142
- References 143
- Abbreviations/Acronyms 145
- Glossary 148
Related products and manuals for Networking Siemens OSM
Networking Siemens CP 1515 Service Manual
(15 pages)
(15 pages)
Networking Siemens CL-010 User Manual
(22 pages)
(22 pages)
Networking Siemens SL2-141 User Manual
(24 pages)
(24 pages)
Networking Siemens 2614 User's Guide
(44 pages)
(44 pages)
Networking Siemens 5890 User Manual
(18 pages)
(18 pages)
Networking Siemens PSFR-CP41 Specifications
(81 pages)
(81 pages)
Networking Siemens SIMATIC TIWAY 1 User Manual
(107 pages)
(107 pages)
Networking Siemens SE105 Specifications
(115 pages)
(115 pages)
Networking Siemens SPC3 User Manual
(11 pages)
(11 pages)
Networking Siemens DTU3005-B Specifications
(88 pages)
(88 pages)
© 2020, manymanuals.com. All rights reserved. | 0.351 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals