Siemens Model 240 Service Manual Page 663
- Page / 750
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
List of Faults and Alarms
Faults and Alarms
3-663
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
F01037 (A) ACX: Re-naming the parameter back-up file unsuccessful
Reaction: NONE (OFF1, OFF2, OFF3)
Acknowledge: IMMEDIATELY
Cause: Re-naming after saving a parameter back-up file in the non-volatile memory was unsuccessful.
One of the parameter back-up files to be re-named had the "read only" attribute. The parameter back-up files are
saved in the directory \USER\SINAMICS\DATA.
It is possible that the non-volatile memory is defective.
Fault value (r0949, interpret hexadecimal):
Byte 1: yyy in the file names PSxxxyyy.* or CAxxxyyy.* or CCxxxyyy.*
yyy = 000 --> consistency back-up file
yyy = 099 --> PROFIBUS parameter back-up file PSxxx099.*
Byte 2: xxx in the file name PSxxxyyy.*
xxx = 000 --> data save started with p0971 = 1
xxx = 010 --> data save started with p0971 = 10
xxx = 011 --> data save started with p0971 = 11
xxx = 012 --> data save started with p0971 = 12
Byte 4, 3:
Only for internal Siemens troubleshooting.
Remedy: - check whether one of the files to be overwritten has the attribute "read only" and change this file attribute to
"writable". Check all of the files (PSxxxyyy.*, CCxxxyyy.*, CAxxxyyy.*) that belong to drive yyy designated in the fault
value.
- replace the memory card or Control Unit.
F01038 (A) ACX: Loading the parameter back-up file unsuccessful
Reaction: NONE (OFF1, OFF2, OFF3)
Acknowledge: IMMEDIATELY
Cause: An error has occurred when downloading PSxxxyyy.ACX or PTxxxyyy.ACX files from the non-volatile memory.
Fault value (r0949, interpret hexadecimal):
Byte 1: yyy in the file name PSxxxyyy.ACX
yyy = 000 --> consistency back-up file
yyy = 001 ... 062 --> drive object number
yyy = 099 --> PROFIBUS parameter back-up file
Byte 2:
255 = incorrect drive object type
254 = topology comparison unsuccessful -> drive object type was not able to be identified
Reasons could be:
- incorrect component type in the actual topology
- component does not exist in the actual topology
- component not active
Otherwise for internal Siemens troubleshooting.
Byte 4, 3:
Only for internal Siemens troubleshooting.
Remedy: - If you have saved the project data using the commissioning software, carry out a new download for your project.
Save using the function "Copy RAM to ROM" or with p0971 = 1 so that all of the parameter files are again completely
written to the non-volatile memory.
- replace the memory card or Control Unit.
- SINAMICS 1
- SINAMICS G120 3
- Control Units CU240B/E-2 3
- Contents 5
- Parameters 1 7
- Fig. 1-1 Read-only parameter 8
- Fig. 1-2 Write parameter 8
- CoBo.pdf 9
- 1.2 List of Parameters 16
- [4] = Phase V offset 37
- [6] = Total U, V, W 37
- Parameters 104
- List of Parameters 104
- Yes No 232
- 1.3.1 Command Data Sets (CDS) 464
- 1.3.2 Drive Data Sets (DDS) 466
- 1.3.3 Motor Data Sets (MDS) 471
- Function diagrams 2 487
- Function diagrams 494
- 2.3 Overview 498
- 499
- ... ... 499
- Overview 500
- 2.4 Input/Output Terminals 506
- Input/Output Terminals 507
- % 100x • 515
- 2.5 Communication 517
- Communication 519
- Internal control/status words 540
- 2.7 Braking Control 557
- Braking Control 558
- 2.8 Safety Integrated 559
- Safety Integrated 560
- Statically inactive 571
- 2.9 Setpoint channel 572
- Setpoint channel 573
- 2.10 V/f control 582
- V/f control 583
- 2.11 Vector control 586
- Vector control 587
- Upper torque limit 595
- Lower torque limit 595
- 2.12 Free Function Blocks 606
- Free Function Blocks 607
- 2.13 Technology functions 627
- Technology functions 628
- 2.14 Technology controller 629
- Technology controller 630
- 2.16 Faults and warnings 644
- Faults and warnings 645
- 2.17 Data sets 649
- Data sets 650
- Faults and Alarms 3 653
- 3.1.1 General information 654
- Faults and Alarms – Overview 655
- Faults and Alarms 655
- 3.1.2 Fault reactions 656
- 3.2 List of Faults and Alarms 658
- List of Faults and Alarms 663
- Appendix A 733
- A.1 ASCII Table (excerpt) 734
- A.2 List for motor code 734
- List of Abbreviations B 735
- List of Abbreviations 736
Related products and manuals for Telephones Siemens Model 240
Telephones Siemens euroset 3020 User Manual
(40 pages)
(40 pages)
Telephones Siemens Gigaset 250 User Manual
(121 pages)
(121 pages)
(58 pages)
Telephones Siemens HiPath AllServe User Manual
(112 pages)
(112 pages)
Telephones Siemens Gigaset SL910A User Manual
(112 pages)
(112 pages)
Telephones Siemens Gigaset A2 Service Manual
(25 pages)
(25 pages)
Telephones Siemens Gigaset N300 IP User Manual
(209 pages)
(209 pages)
Telephones Siemens 2060isdn User's Guide
(110 pages)
(110 pages)
© 2020, manymanuals.com. All rights reserved. | 2.649 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals