Siemens HB86P.75 Instruction Manual Page 19

  • Download
  • Add to my manuals
  • Print
  • Page
    / 40
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 18
19
Error messages with E
If an error message with E is shown in the display, press the 0
button. Then reset the clock. This cancels the error message. If
the error is shown again, call the after-sales service. With error
message E106, you can still operate the microwave.
If error message E011 is displayed, a button may have become
stuck. Press each button individually and check that they are all
clean. If the error message remains, please contact the after-
sales service.
Replacing the oven light bulb
It is possible to replace the oven light. Heat-resistant 12 V,
20 W halogen bulbs can be obtained from After-sales Service
or a specialist retailer.
ã=Risk of electric shock!
Never replace the oven light when the appliance is switched on.
Pull out the mains plug or switch off the appliance at the circuit
breaker in the fuse box.
Note: Always remove the new halogen bulb from the packaging
using a dry cloth. This increases the service life of the bulb.
Method
1. Switch off the circuit breaker in the fuse box.
2. Place a tea towel in the cold oven to prevent damage.
3. Remove the glass cover. To do so, prise open the glass
cover at the bottom by hand.
Should you experience difficulties removing the glass cover,
use a spoon to help. (Fig. A)
4. Remove the bulb and replace with a bulb of the same type.
(Fig. B)
5. Refit the glass cover. (Fig. C)
6. Remove the tea towel. Switch the circuit breaker in the fuse
box back on or plug in the mains plug.
“Set clock” appears in the status
bar. The time displayed is not the
current time. “Select language”
appears in the settings area on the
right.
Power cut Turn the rotary selector to set the correct time
then press the
0 button. The language set
remains unchanged following a power cut.
The oven door cannot be opened.
“Set clock” appears in the status
bar. The time displayed is not the
current time. “Select language”
appears in the settings area on the
right. The
H symbol is displayed.
Power cut during self-cleaning operation Turn the rotary selector to set the correct time
then press the0 button. The language set
remains unchanged following a power cut.
Wait until the cooking compartment has
cooled down. The H symbol goes out. You
can open the oven door again.
The oven does not heat up.
“Demo” is displayed in the status
bar.
The oven is in demo mode Switch off the circuit breaker in the fuse box
and then switch back on after approx.
20 seconds. Within the next 2 minutes, press
and hold the @ button for four seconds until
“Demo” disappears from the status bar.
The oven does not heat up or the
type of heating selected cannot be
set.
Type of heating not recognised. Set once again.
Automatic switch-off” appears in
the status bar.
Automatic switch-off has been activated. The
oven switches off.
Press any button. The text disappears. You
can make settings again.
The microwave does not switch
on.
Door not fully closed. Check whether food remains or foreign mate-
rial is trapped in the door. Make sure that the
sealing surfaces are clean. Check whether the
door seal is twisted.
The microwave was not started.
Press the
button.
The appliance does not heat up to
the temperature which has been
set.
The
button was not pressed. Press the button.
Microwave operation has been
cancelled for no apparent reason.
The microwave has a fault. If this fault occurs repeatedly, please call the
after-sales service. Oven operation without
microwave is possible.
With microwave operation, the
food takes longer to heat up than
before.
The microwave power setting is too low. Select a higher power setting.
A larger amount than usual has been placed in
the appliance.
Double the amount = almost double the time
The food was colder than usual. Stir or turn the food during cooking
Problem Possible cause Remedy/information
$
%
&
Page view 18
1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 39 40

Comments to this Manuals

No comments