Siemens v1.0 Service Manual Page 54
- Page / 202
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Simple example
2.5 Test program
STEP 7 Basic V10.5
54 Getting Started, 12/2009, A5E02651459-01
2.5.2 Test program with program status
Introduction
The following steps show you how to test the created program with program status. If you
display the program status, you can monitor the execution of the program. You can enable
the status starting at a specific location in the program and you then obtain an overview of
the values of the individual tags and the results of logic operations. This allows you to check
whether or not the components of the automation system are being correctly controlled.
The display of the program status is updated cyclically. It begins at the selected network.
In the program status you can allocate values to the tags by performing one of the following
actions using the "Modify" command of the shortcut menu:
● Modify to 1: Use this command to set the tags of the BOOL data type to the signal state
"1".
● Modify to 0: With this command you set the tags of the BOOL data type to the signal state
"0".
● Modify value: You can enter a modify value for tags that are not of the BOOL data type.
Requirements
● The PLC is configured.
● There is no voltage at the inputs and outputs of the PLC, because the modified values
are overwritten by the module in online mode.
● The organization block "Main [OB1]" is opened in the program editor.
Procedure
To test the created program with program status, follow these steps:
1. Enable monitoring.
The program status is displayed.
- SIMATIC 1
- TIA Portal 1
- STEP 7 Basic V10.5 1
- Legal information 2
- Table of contents 3
- 1.1 Overview 6
- 1.2 TIA Portal basics 7
- 7,$3RUWDO 8
- 8QLIRUPHQJLQHHULQJV\VWHP 8
- :LQ&&%DVLF9 8
- 67(3%DVLF9 8
- 1.2.3 Data management 9
- Library concept 10
- 1.3 Views in the TIA portal 11
- 1.3.2 Portal view 12
- 1.3.3 Project view 13
- TIA Portal Introduction 14
- 1.3 Views in the TIA portal 14
- 1.4 Example projects 15
- 1.4 Example projects 16
- 1.4.2 Loading a project 17
- TIA Portal Introduction 19
- 1.4 Example projects 19
- Simple example 21
- 2.3.1 Inserting a PLC 23
- Simple example 25
- Network view 26
- Device view 28
- 2.3.3 Configure PLC 29
- 2.4 Create program 31
- 2.4 Create program 33
- 2.4 Create program 34
- 2.4.4 What are networks? 35
- LAD instructions 36
- Normally open contact 37
- Negated coil 38
- 2.4.6 What are tags? 42
- PLC tag table 44
- 2.5 Test program 48
- 2.5 Test program 50
- 2.5 Test program 51
- Additional information 53
- +0, 3/& 3URFHVV 57
- Adding a new HMI device 58
- 2.6 Create HMI screen 59
- 2.6 Create HMI screen 60
- Graphic objects 65
- Use of graphic objects 65
- External HMI tags 66
- Internal HMI tags 77
- 2.7 Testing HMI screen 85
- 2.7.2 Simulate runtime 87
- 2.7 Testing HMI screen 88
- 3.1 Introduction 90
- 3.2 Expanding the program 91
- Normally closed contact 97
- Extended example 100
- 3.2 Expanding the program 100
- 2SHUDQG! 101
- Procedure 102
- Requirements 103
- Introduction 103
- Extended example 105
- 3.2 Expanding the program 105
- On delay 110
- Output coil 110
- 3.4 Expand HMI screen 123
- 3.4 Expand HMI screen 124
- 3.4 Expand HMI screen 129
- 3.5 Simulate HMI screen 132
- Testing in the HMI device 133
- 3.5 Simulate HMI screen 134
- 4.1 Introduction 135
- Use of the PID controller 136
- 4.1 Introduction 137
- STEP 7 Basic V10.5 140
- 4.4 Load simulation block 143
- 4.4 Load simulation block 144
- 4.4 Load simulation block 145
- 4.5 Configure PID controller 150
- Block name 151
- Parameter 151
- 4.8 Adjust HMI screen 158
- 4.8 Adjust HMI screen 159
- 4.8 Adjust HMI screen 160
- Controller optimization 161
- Example "Motion" 165
- Hardware configuration 166
- Example "Motion" 167
- 5.1 Introduction 167
- 5.4 Enable axis 173
- 5.4 Enable axis 174
- 5.4 Enable axis 175
- 5.5 Position axis relative 176
- 5.5 Position axis relative 177
- 5.5 Position axis relative 178
- 5.6 Expand HMI screen 180
- 5.6 Expand HMI screen 181
- 5.6 Expand HMI screen 184
- 5.7 Simulate HMI screen 189
- 5.7 Simulate HMI screen 190
- 5.8 Start diagnostics view 191
- 5.8 Start diagnostics view 192
- 5.8 Start diagnostics view 193
- Glossary 197
- Glossary 199
Related products and manuals for Software Siemens v1.0
Software Siemens S7-400 Service Manual
(382 pages)
(382 pages)
Software Siemens AC65 User's Guide
(123 pages)
(123 pages)
Software Siemens Simatic M7-400 User Manual
(266 pages)
(266 pages)
© 2020, manymanuals.com. All rights reserved. | 0.270 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals