Siemens SIMATIC PANEL PC 877 Operations Instructions Page 42
- Page / 238
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Connecting
5.5 Equipotential bonding with stainless steel front
SIMATIC IPC677C
42 Operating Instructions, 05/2010, A5E02722710-01
Steps for connecting the equipotential bonding
(1) Connect the equipotential bonding connection (M4 thread) (1)
on the device (large surface, large-area contact) with the
central grounding point of the control cabinet.
The minimum permissible cross-section is 5 mm
2
.
5.5 Equipotential bonding with stainless steel front
Information on devices with stainless steel front
CAUTION
Ensure proper electrical contact between the enclosure of the device and the switchboard.
The conductive surfaces of the clamping frame and of the switchboard should have proper
contact.
5.6 Connecting Ethernet/USB strain relief
The Ethernet/USB strain relief supplied in the product package is used to prevent accidental
removal of the Ethernet cable and Industrial Ethernet FastConnect connector from the
device. You need two cable ties to use the strain relief. In addition to the Ethernet cables,
you can also use this strain relief to protect the four USB cables from inadvertent removal.
To secure the Ethernet strain relief, you will need a TORX T10 screwdriver.
Steps for connecting the Ethernet/USB strain relief
1
Fasten the Ethernet/USB strain relief ① to the device
enclosure with two oval-head screws (M3 thread).
2 Connect the network/USB cable and attach it to the
strain relief using cable ties ②.
- SIMATIC 1
- Industrial PC 1
- SIMATIC HMI IPC677C 1
- Preface 3
- Conventions 4
- Trademarks 4
- Table of contents 7
- Table of contents 10
- 1.1 Safety guidelines 11
- 1.2 General Information 12
- Transport 13
- Tools & downloads 13
- Optical drive 13
- Safety-relevant applications 13
- Safety 14
- 1.2 General Information 14
- 1.3 ESD directives 15
- Shipping ESD modules 16
- Description 17
- Key panel variants 18
- Description 19
- 2.3 Accessories of IPC677C 20
- Planning the use 21
- Rating plate 22
- COA label 23
- Approval 25
- 3.4.4 Type of fixation 26
- 3.5 Mounting cutout 27
- 3.5 Mounting cutout 28
- 3.6 EMC Guideline 29
- 3.6 EMC Guideline 30
- Mounting 31
- 4.2 Securing with screws 32
- IP54 degree of protection 33
- Introduction 33
- Procedure 33
- Connecting 35
- AC power supply 36
- DC power supply 37
- Localized information 38
- ①, if necessary 39
- Connecting 41
- ① to the device 42
- 6.1 Overview 45
- SIMATIC NET 46
- Additional information 46
- Coupling 46
- Hardware requirements 46
- 6.5 PROFINET 48
- Further information 49
- 6.5 PROFINET 50
- Commissioning 51
- See also 52
- 7.5 Additional applications 53
- 7.5.1 Touch Panel set-up 54
- 7.5.2 Key Panel adjustment 55
- 7.6 BIOS settings 56
- 7.7 USB 56
- 7.8 Notes on operation 57
- 7.8 Notes on operation 58
- Commissioning 59
- 7.8 Notes on operation 59
- Comments about faults 60
- Characteristics 60
- Flash drive functions 61
- Booting from the Flash drive 61
- Operation and configuration 63
- 8.2 Normal operation 64
- Calling up KeyTools 70
- Call "Touch input" 70
- 8.3.7 Panel PC Tools 71
- 8.3.8 CheckLanguageID 72
- Operation 75
- 9.2 Device with key panel 76
- 9.2.3 Keys 77
- Numeric keys 78
- 9.2.4 External keyboards 79
- 9.3 Device with touch panel 81
- Touch pen 82
- 9.3 Device with touch panel 84
- Functions 85
- 10.3 Watchdog (WD) 86
- 10.4 Fan monitoring 87
- 10.5 SRAM buffer memory 87
- 10.6 Battery monitoring 87
- 10.6 Battery monitoring 88
- Resistance to chemicals 90
- Scope of maintenance 90
- Cleaning the front membrane 91
- Front membrane 92
- Resistance 92
- Cleaning guidelines 92
- 11.5 Spare parts 93
- 11.7.1 Opening the Device 96
- 11.7.2 Memory expansion 97
- Installing a memory module 98
- Removing a memory module 98
- Inserting the slider 100
- Service and maintenance 101
- Preparations 102
- ① on the DVD 103
- ① of the 104
- ① the drive 104
- Preparation 105
- Installing an SSD drive 105
- Memory expansion options 106
- Opening the board slot 106
- ① and remove 109
- 11.8.1 Repairs 110
- Disclaimer of liability 111
- Disposal 112
- Replacing the battery 112
- Reconfiguring the BIOS setup 113
- ① from the 114
- ① on the bus 115
- ②. Remove the 116
- Installing the fan 119
- Removing the fan 119
- ① on the 120
- Restoring factory state 121
- Service and maintenance 122
- 11.9 Installing the software 122
- Partitioning the hard disk 127
- 11.9.4 RAID1 system setup 128
- 11.9.6 Installing updates 131
- 11.9.7 Data backup 132
- 11.9.8 CP 1616 onboard 132
- 12.1 Boot error messages 133
- Example 134
- 12.3 BIOS beep codes 135
- 12.3 BIOS beep codes 136
- 12.3 BIOS beep codes 137
- Special codes 141
- Troubleshooting/FAQs 143
- 13.1 General problems 144
- Troubleshooting/FAQs 145
- Technical data 147
- 14.1 General specifications 148
- Technical data 149
- Maximum current values 153
- Typical power values 153
- 14.4 AC voltage supply 154
- 14.5 DC power supply 155
- 14.6 Keyboard table 156
- 14.6 Keyboard table 157
- 14.6 Keyboard table 158
- Dimensional drawings 163
- 15.1 Dimension drawing IPC 164
- Dimensional drawings 165
- Detailed descriptions 167
- 16.1 Motherboard 168
- Detailed descriptions 169
- 16.1 Motherboard 169
- ; ; ; ; ; ;; ; 170
- PROFIBUS/MPI interface X4 171
- DVI-I port, X70 173
- Compact Flash card, X50 174
- 16.1.5 Internal interfaces 175
- 16.1.6 Front ports 177
- 16.2 Bus board 181
- 16.2 Bus board 182
- 16.2 Bus board 183
- 16.3 System resources 185
- 16.3 System resources 186
- 16.3 System resources 187
- 16.4 BIOS Setup 190
- Menu layout 191
- 16.4.4 Main menu 192
- 16.4.5 Advanced menu 193
- 16.4 BIOS Setup 194
- 16.4 BIOS Setup 195
- 16.4.6 Security menu 201
- 16.4.7 Power menu 202
- 16.4.8 Boot Menu 203
- 16.4.9 Version Menu 206
- 16.4.10 Exit menu 207
- BIOS Setup default settings 208
- 16.5.1 Introduction 212
- CP 1616 onboard as IO device 213
- 16.5.2 Firmware loader 214
- 16.5.2.1 Loading firmware 215
- Start downloading procedure 215
- Configuring 216
- Appendix 217
- Product safety 219
- +$=/2& 220
- Electrostatic charging 221
- B.1 Abbreviations 223
- B.1 Abbreviations 224
- B.1 Abbreviations 225
- Glossary 227
- Glossary 229
- SIMATIC IPC677C 233
- SIMATIC IPC677C 234
- Index 235
Related products and manuals for PC/workstation barebones Siemens SIMATIC PANEL PC 877
(52 pages)
(192 pages)
(276 pages)
(80 pages)© 2020, manymanuals.com. All rights reserved. | 0.870 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals