Siemens PC 870 Operations Instructions Page 81
- Page / 168
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Alarm, error and system messages
12.2 BIOS beep codes
Panel PC 870 V2, Computer Unit
Operating Instructions, Edition 03/2004, CD Documentation and Drivers
12-3
Beep sequence hex Description
1-1-1-3 02 Test whether the CPU is in real mode
1-2-4-1 1C Reset the interrupt controller
4-1-3-2 C9 Checksum test
1-2-1-3 12 Restore the controller register
1-2-1-4 13 PCI Bus Master Reset
1-4-2-3 36 Check shutdown code
1-3-2-1 24 Switch the ES to special mode
1-1-1-4 03 Switch off NMI
1-1-3-3 0A Pre-initialization of the CPU
1-1-2-1 04 Determine the CPU type
3-3-4-3 AE Edit boot flag
1-1-2-3 06 Initialize basic hardware
1-2-3-1 18 Initialize timers
1-1-3-1 08 Initialize the chip set
4-1-2-1 C4 Reset system error message
1-2-1-2 11 Initialize Registry
1-1-4-3 0E Initialize IO
1-1-4-1 0C Initialize cache
1-2-2-3 16 EPROM checksum test
1-2-2-4 17 Initialize external cache before autosizing memory
1-3-3-1 28 Determine RAM size
1-4-3-3 3A Determine cache size
1-3-3-3 2A Set 512 kB base RAM to 0
1-3-4-1 2C Test address channels in basic RAM
1-3-4-3 2E Check first 64 KB in basic RAM
1-3-4-4 2F Initialize external cache before shadowing BIOS
1-4-3-1 38 BIOS shadow
1-3-1-1 20 Refresh circuit test
1-3-3-2 29 Initialize the POST memory manager
1-4-1-4 33 Initialize the dispatch manager
4-1-1-2 C1 Initialize the POST Error Manager
1-1-3-2 09 Start Power On Self Test
1-1-3-3 0A Initialize CPU
1-1-3-4 0B Switch on cache
1-1-4-4 0F Initialize hard disk
1-2-1-1 10 Initialize power management
1-2-2-1 14 Initialize block 8742
1-2-3-3 1A Initialize the DMA circuits
1-2-4-1 1C Reset the interrupt controller
1-4-1-3 32 Determine the clock pulse speed
4-1-1-2 69 Initialize the handler for SMM
1-4-2-1 34 Test the CMOS RAM
- SIMATIC PC 1
- Panel PC 870 V2 1
- Computer Unit 1
- Table of contents 3
- Table of contents 5
- Preface 7
- 1.1 This manual 8
- Conventions 9
- Trademarks 9
- 1.2 Further Support 10
- A&D Technical Support 11
- 2.1 Safety information 13
- Battery 14
- 2.2 General notes 15
- Description 17
- 3.3 Features 18
- Description 19
- 3.3 Features 19
- Planning use 21
- Procedure 22
- Planning use 23
- Range of validity 25
- Installation 27
- 5.2 Dimensions 28
- Connecting 29
- 6.2 Interfaces 30
- AC power supply 31
- 6.3 Equipotential bonding 32
- Connecting 33
- 6.5 Connecting I/O modules 34
- Principle 35
- Localized information 35
- For USA and Canada: 36
- 120V power supply 36
- 230V power supply 36
- Commissioning 39
- 7.3.1 Releases 40
- 7.3.2 Windows 2000 40
- 7.4 USB 41
- Simplified block diagram 42
- Operation 43
- 8.2 Floppy drive 44
- Integration 45
- Interconnection 46
- Hardware requirements 46
- Integration 47
- Functions 49
- 10.3 Watchdog (WD) 50
- 10.4 Fan monitoring 50
- Functions 51
- Maintenance and servicing 53
- 11.1.2 Open the device 54
- Memory expansion options 55
- Preparation 55
- Installing the memory module 56
- Removing a memory module 56
- Maintenance and servicing 57
- Inserting the slider 58
- 11.1.5 Disk drives 59
- Remove the hard disk bay 60
- Disposal 65
- Replacing the battery 66
- BIOS Setup readjustment 66
- 11.2 Installing software 68
- Recovery CD: 69
- Restore CD: 69
- 11.2 Installing software 70
- 11.2 Installing software 71
- Factory state restoring 72
- Windows 2000 Setup sequence 72
- Introduction 76
- Booting from the slave drive 77
- New software installation 77
- 12.1 Boot error messages 79
- 12.2 BIOS beep codes 80
- 12.2 BIOS beep codes 81
- 12.2 BIOS beep codes 82
- Troubleshooting and FAQs 85
- 13.3 Temperature error 86
- Specifications 87
- 14.1 Specifications 88
- Specifications 89
- 14.1 Specifications 89
- Standard system 90
- 14.1.3 AC power supply 91
- 14.1.4 DC power supply 92
- 14.2 Dimensional drawings 93
- 14.2 Dimensional drawings 94
- 14.2 Dimensional drawings 95
- Interfaces 98
- 15.1.3 External ports 99
- Parallel port LPT1, X134 100
- PS/2 mouse port, X22 101
- PS/2 keyboard port, X23 101
- USB ports, X36 102
- PROFIBUS/MPI interface, X400 102
- DVI interface, X303 103
- 15.1.4 Front interfaces 104
- Detailed descriptions 105
- 15.1 Motherboard 105
- Detailed descriptions 106
- 15.1 Motherboard 106
- 15.1.5 Internal interfaces 108
- 15.2 Bus board 112
- 15.2 Bus board 113
- Overview 114
- ISA slot pin assignment 115
- PCI slot pin assignment 116
- 15.3 Cables 118
- 15.4 System resources 118
- 15.4 System resources 119
- 15.4 System resources 120
- 15.5 BIOS Setup 123
- 15.5.3 BIOS Setup menus 124
- 15.5.4 Main menu 125
- Settings in the main menu 126
- 15.5 BIOS Setup 127
- 15.5 BIOS Setup 128
- 15.5.5 Advanced menu 133
- Internal printer port LPT1 135
- 15.5.6 Security menu 138
- 15.5.7 Power menu 139
- 15.5.8 Boot menu 140
- 15.5.9 Version menu 141
- 15.5.10 Exit menu 142
- BIOS Setup-Defaults 143
- Appendix 147
- Appendix 149
- 16.1.3 ESD guideline 150
- 16.2 Abbreviations 153
- 16.3 Glossary 154
- 16.3 Glossary 155
- 16.3 Glossary 156
- Index 164
- Index 165
Related products and manuals for PC/workstation barebones Siemens PC 870
(32 pages)© 2020, manymanuals.com. All rights reserved. | 1.226 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals