Siemens 2614 User's Guide

Part No. 007-0207-001SpeedStreamSpeedStreamSpeedStreamSpeedStream®26144-Port DSL/Cable Router4-Port DSL/Cable Router4-Port DSL/Cable Router4-Port DSL/

2-5If Internet services are provided through an xDSL or cable modem, use unshielded or shielded twisted-pair Ethernet cable with RJ-45 plugs to connec

2-67. Configure the SpeedStream 2614. Configure the SpeedStream 2614 as detailed in Chapter 3, “Configuring the SpeedStream 2614.”.8. Configure TCP/IP

3-1CHAPTER 3CONFIGURING THE SPEEDSTREAM 2614Before you can configure the SpeedStream 2614 DSL/Cable Router, the TCP/IP protocol must be installed on a

3-2client filtering, and various other settings.•Tools – Reset the SpeedStream 2614, restore the factory settings, or upgrade on-board firmware. •Help

3-3Configuration ChangesConfigurable parameters are available by means of dialog boxes or drop-down lists. After you change a configuration, be sure t

3-4The Status screen provides the following information: Table 3-2. Status Menu OptionsSimple Setup ProceduresThe management interface will guide you

3-52. On the Simple Setup menu, click Set Time Zone.3. On the Set Time Zone screen, select the correct time zone in the drop-down list box.4. Click En

3-6Static IP Address (Fixed IP)If your selected Static IP Address as your WAN connection type, the Simple Setup | WAN | Fixed IP screen displays when

3-7fill in the relevant fields under Secondary Dial-up.Figure 3-3. Simple Setup | WAN | Dial-up Modem1. In the Check if you only use a dial-up modem

3-8address for you to use, select Ye s and enter the designated IP address and subnet mask.Advanced Setup ProceduresAfter completing the Simple Setup

iTABLE OF CONTENTS1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

3-9Enable Firewall ProtectionFrom the Advanced Setup | Firewall screen, you can enable the SpeedStream 2614 firewall to block common hacker attacks, i

3-10information.4. Click Copy to to enter that information in the Public Port boxes on the designated line.Network Address Translation (NAT)Network Ad

3-113. Click in the box to the right of Copy to and select the line number to which the system will enter that information.4. Click Copy to to enter t

3-12a DMZ host. Caution:Adding a client to the DMZ (demilitarized zone) may expose your local network to a variety of security risks. Use this option

3-13Reset RouterOn the Tools menu or screen, click Reset Router to reboot the router and retain all your configuration settings.Restore Factory Defaul

4-1CHAPTER 4INSTALLING AND CONFIGURING TCP/IPTo access the Internet through the SpeedStream 2614 DSL/Cable Router, you must configure it and your netw

4-2Figure 4-2. Select Network Protocol6. The TCP/IP protocol will be listed in the Network window. Click OK to complete the install procedure, and re

4-34. Click OK and reboot your system to implement the changes.Figure 4-3. TCP/IP Properties SheetsManual IP Configuration1. On the IP Address tab, s

4-4However, if the following message appears, there may be something wrong in your installation procedure: Pinging 192.168.254.254 with 32 bytes of da

5-1CHAPTER 5CONFIGURING PRINTER SERVICESThe SpeedStream 2614 printer server supports Windows 95/98/NT/2000/ME and Unix platforms. To configure print s

ii5 Configuring Printer Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1Install the Print Server P

5-2specified location.Figure 5-2. Choose Destination Location4. Select the folder to contain the program icons; then click Next. Figure 5-3. Select

5-35. Enter the printer port name that will identify the port monitor in your system; then click Next.Figure 5-4. Select Port Name6. When the setup p

5-4Configure the Printer PortAfter you install the print server program, locate the instructions below that are specific to your operating system: Win

5-53. Select the port you want to use with this printer; then click Next. Figure 5-8. Select Printer Port4. Follow the prompts to complete the SpeedS

5-62. Select Local printer; then click Next.Figure 5-10. Select Network Printer

5-73. Select the printer port; then click Next. Figure 5-11. Select Printer Port4. Follow the prompts to complete the printer port configuration. The

A-1Appendix ATROUBLESHOOTINGThis section describes common problems you may encounter and their possible solutions. Use the panel indicators to monitor

A-2Table A-1. Troubleshooting ChartTechnical SupportBefore contacting Technical Support, please refer to the previous Troubleshooting table. If you a

B-1Appendix BCABLESEthernet CableCable Types and SpecificationsTable B-1. Cable Types and SpecificationsTwisted-pair CableCaution: DO NOT plug a phon

B-2RJ-45 Pin NumberingTable B-2. RJ-45 Pin NumberingRJ-45 Pin AssignmentsAll LAN ports on the SpeedStream 2614 support automatic MDI/MDI-X configura

1-1CHAPTER 1INTRODUCTIONCongratulations on your purchase of the SpeedStream 2614 DSL/Cable Router. Siemens is proud to provide you with a powerful yet

B-3DB-9 Port Pin AssignmentsTable B-4. DB-9 Port Pin AssignmentSerial Port to 9-Pin COM Port on ComputerTable B-5. Serial Port to 9-Pin COM Port on

B-4Serial Port to 25-Pin DTE Port on ComputerTable B-7. Serial Port to 25-Pin DTE Port on ComputerPrinter Port Pin AssignmentsThe DB-25 parallel port

B-5DB-25 Printer Port Pin AssignmentsTable B-8. DB-25 Printer Port Pin AssignmentPin Signal Name Direction 1 -Strobe To printer 2 +Data 0 To printe

C-1APPENDIX CSpecificationsWAN Interface10BASE-T, 1 RJ-45 port(1) DB-9 RS-232 port for PSTN/ISDN connectionsLAN Interface10BASE-T/100Base-TX(4) RJ-45

C-2TemperatureOperating 32 to 104°F (0 to 40°C)Storage -40 to 158°F (-40 to 70°C)Humidity5% to 95% (noncondensing)

1-2ApplicationsThe SpeedStream 2614 by Siemens provides many advanced features and functionality:•LAN Access – The SpeedStream 2614 provides connectiv

2-1CHAPTER 2INSTALLING THE SPEEDSTREAM 2614Before installing the SpeedStream 2614 DSL/Cable Router, verify that you have all the items listed under “P

2-2These ports can auto-negotiate the operating speed to 10/100 Mbps, the mode to half/full duplex, and the pin signals to MDI/MDI-X, allowing these

2-3System RequirementsYou must have access to a network that meets the following minimum requirements:• Internet access from your local telephone comp

2-4Figure 2-2. Connecting the SpeedStream 2614CautionDo not plug a phone jack connector into any RJ-45 port. This may damage the SpeedStream 2614. In