Siemens SIMATIC TI505 Service Manual Page 1

SiemensTI305, TI405, TI505Manuals and GuidesPresented By: Siemens SupplyFor Product Needs Please Visit:http://www.siemenssupply.com/OR email:sales@sie

Chapter 1: Introduction 7 Cable P/N 0818 (PanelMate Power Series 1500 and PanelMate 500 only) www.siemenssupply.com

8 Texas Instruments Communication Driver Manual Memory The 500 Series driver supports the following memory types. Memory Type Memory Address 16 Bit

Chapter 1: Introduction 9 The 405 Series driver supports the following memory types. Memory Type Memory Address 16-Bit Word TMR Timer CNT Count

10 Texas Instruments Communication Driver Manual The 305 Series driver supports the following memory types. Memory Type Memory Area 16-Bit Word AC

Chapter 1: Introduction 11 Memory Ranges for the 500 Series Driver The 500 Series driver supports the following memory types and ranges. Memory Typ

12 Texas Instruments Communication Driver Manual Memory Ranges for the 405 Series Driver The 405 Series driver supports the following memory types an

Chapter 1: Introduction 13 Memory Ranges for the 305 Series Driver The 305 Series driver supports the following memory types and ranges. Memory Typ

14 Texas Instruments Communication Driver Manual Possible Configurations 2 In this chapter, you will learn: How to connect an operator station to Tex

Chapter 2: Possible Configurations 15 Direct Connection See the TI manual for your PLC to set the baud rate for the port on the CPU. Connection to

16 Texas Instruments Communication Driver Manual Cabling 3 In this chapter, you will learn: The cabling requirements for Texas Instruments PLCs • ww

PanelMate Texas Instruments Communication Driver Manual Eaton Corporation Cutler-Hammer Business Unit 811 Green Crest Drive Columbus

Chapter 3: Cabling 17 Communication between the Operator Station and the TI PLCs Communications between the Operator Station and TI 500 PLCs is ach

18 Texas Instruments Communication Driver Manual Cable Catalog Number: TI23 RS422 Cabling for TI 305, 405, 435, 505, 545, and 555 PLCs Cable Catalog

Chapter 3: Cabling 19 Cable Catalog Number: TI26A Cable Catalog Number: TI27A www.siemenssupply.com

20 Texas Instruments Communication Driver Manual RS232C Cabling for TI PLCs The Operator Stations that have RJ-11 6-wire and RJ-45 modular jacks must

Chapter 3: Cabling 21 RS422 Cabling for TI 405, 305, and 545 PLCs www.siemenssupply.com

22 Texas Instruments Communication Driver Manual Communication Parameters 4 In this chapter, you will learn: The different switch settings • www.sie

Chapter 4: Communications Parameters 23 Dual Communication Port Module TI 500 Series The Dual Communication Port Module (DCPM) has two RS232/423 po

24 Texas Instruments Communication Driver Manual Serial Interface Port TI 435 PLC The Serial Interface Port enables the TI 435 PLC to interface direc

Chapter 4: Communications Parameters 25 The table below shows the pinouts for the Serial Interface Port. Pin Name Pin Name 1 Not Used 14 TXD+ 2

26 Texas Instruments Communication Driver Manual Dipswitch Settings The dipswitch block is located at the rear of the CPU. The table below summarize

Preface Information in this manual is subject to change without notice and does not represent a commitment on the part of Eaton’s Cutler-Hammer, Inc.

Chapter 4: Communications Parameters 27 Data Communication Module (DCM) TI 405 Series The Data Communication Module (DCM) enables the TI Series 405

28 Texas Instruments Communication Driver Manual There are two rotary switches on the DCM that select the network address of the PLC. This address m

Chapter 4: Communications Parameters 29 Switch 3 and 4 of dipswitch 2 should be set to OFF to enable communication timeout and to allow data to be

30 Texas Instruments Communication Driver Manual Data Communication Unit (DCU) TI 305 Series The Data Communication Unit (DCU) enables the TI Series

Chapter 4: Communications Parameters 31 There are two dipswitches located on the DCU. Dipswitch 1 selects the baud rate and internal functions. S

32 Texas Instruments Communication Driver Manual Bit Writes with Ladder Logic – 405 Series The Texas Instruments Hostlink Protocol does not permit an

Chapter 4: Communications Parameters 33 www.siemenssupply.com

34 Texas Instruments Communication Driver Manual www.siemenssupply.com

Chapter 4: Communications Parameters 35 Bit Writes with Ladder Logic – Model 315 The Texas Instruments Hostlink Protocol does not permit an externa

36 Texas Instruments Communication Driver Manual PLC ID The format for the PLC ID for the model 315 will include both the PLC ID and a memory registe

www.siemenssupply.com

Chapter 4: Communications Parameters 37 Bit Writes with Ladder Logic – Models 325 and 330 The Texas Instrument Hostlink Protocol does not permit an

38 Texas Instruments Communication Driver Manual If an AC memory address in not entered, the Bit Write register will default to AC677. The following

Chapter 5: Word and Bit References 39 Word and Bit References 5 In this chapter, you will learn: How to configure word and bit references • www.

40 Texas Instruments Communication Driver Manual Word Referencing Method The general word referencing method is: [plcname,word#format] The "plc

Chapter 5: Word and Bit References 41 TI 405 Series Word, Byte, and Bit References Texas Instruments 405 PLCs use octal word addresses. The Operat

42 Texas Instruments Communication Driver Manual TI 305 Series Word and Bit References Texas Instruments 305 PLCs use octal word addresses. The Oper

Chapter 5: Word and Bit References 43 The following is the format for a bit referenced within a word. [XY/B] X Memory type (AC and R - for 325 and

44 Texas Instruments Communication Driver Manual Examples The following are examples of valid PLC references that may be assigned in the Operator Sta

Chapter 5: Word and Bit References 45 405 Series Word References Reference Description [TMR11] Timer register 12 [CNT30] Counter register 30 [V24

46 Texas Instruments Communication Driver Manual 305 Series Word References Reference Description [AC614] Timer/Counter register 614 [W:R502] Data

2 Texas Instruments Communication Driver Manual Support Services The goal of Eaton’s Cutler-Hammer business unit is to ensure your greatest possible

Chapter 6: Maintenance Access 47 Maintenance Access 6 In this chapter, you will learn: How to use the Maintenance Template • www.siemenssupply.c

48 Texas Instruments Communication Driver Manual Maintenance Access The Maintenance Template will access all memory locations supported by the PLC dr

Index 49 Index B Bit Writes with Ladder Logic 315 Model, 35 325 and 330 Models, 37 405 Series, 32 C Connection to a DCPM, 15 Connection to a DCU, 1

Reader Comment Card Cutler-Hammer strives to provide quality user guides and product manuals. Please take a moment to fill out this comment card. Ti

Table of Contents 3Table of Contents Introduction...

4 Texas Instruments Communication Driver Manual Introduction 1 In this chapter, you will learn: About driver installation • • • How to download drive

Chapter 1: Introduction 5 Introduction The Operator Station can be used with the programmable controllers in the Texas Instruments (TI) 500 Series

6 Texas Instruments Communication Driver Manual Downloading Drivers to a PanelMate Unit • In the VCP Transfer Utility, choose the “Executive” tab an