Siemens LFL Series User Manual download pdf (Page 3)

FENWALL BURNER CONTROL C/W

WIRING LOOM

12 VDC•

Integral Ignition transformer•

Inter purge time 25 seconds•

Trial for ignition time ( TFI ) 10 •

seconds

# FW-35-53056-035

System Control Engineering NZ Ltd For Gas Combustion & Control Equipment

Tel : 09-636-1401 • Fax: 09-636-1525 • [email protected] • www.systemcontrol.co.nz

Programmed oil & gas Burner Controls

A Honeywell Company

300e/04 /98

For 1- or 2-stage oil power burners up to

30kg/h capacity and intermittent operations.

Flame detection:

- Photoresistor FZ 771 S

- Infrared-flicker detector IRD 1010

- UV solid state sensor UVD 970

Oil Burner Safety Control

TF 801 / 801.2

TF 802 / 802.2

TECHNICAL DATA

Operating voltage 220/240 V (-15..+10%)

50 Hz (40-60Hz)

Fuse rating 10 A fast, 6 A slow

Power consumption ca. 5 VA

Max. load per output

- terminal 3 1.5 A, cos ϕ 0.2

- terminal 4 4 A, cos ϕ 0.4

- terminal 5 0.5 A, cos ϕ 0.4

- terminal 6 0.5 A, cos ϕ 0.4

- terminal 7 0.1 A, cos ϕ 0.4

total load 5A, cos ϕ 0.4

Pre-purge time ca. 12 sec.

Pre-ignition time ca. 12 sec.

Post-ignition time TF 801/TF801.2 ca. 20 sec.

TF 802/TF802.2 ca. 2-4 sec

Delay time to oil valve 2 40 sec. (TF 802)

Lockout safety time 10 sec.

Reset time from lockout ca. 90 sec

Flame detector:

FZ 771 S red side-on viewing

FZ 771 S white side-on and end-on

viewing

Light sensitivity FZ 711S > 10 Lux

IRD 1010 side-on or end-on

viewing

UVD 970 end-on viewing

Weight incl. wiring base 0.25 kg

Mounting position any

Protection class IP44

Recommended ambient operating

temperature for control and

flame detector 0°C...+60°C

approved and certified according

to European standards

TF 801.2/TF802.2 EN 230

TF 801/TF802 DIN 4787

APPLICATION RANGE

The TF 801 or TF 802 oil burner safety control boxes are

suitable to control and monitor oil power burner up to 30 kg/

h capacity (approved and certified according to DIN 4787).

The control boxes TF 801.2 and TF 802.2 are approved and

certified according to EN230.

TYPES AVAILABLE

TF 801 1-stage operation

post-ignition time ca. 20 sec.

TF 801.2 1-stage operation

post-ignition time ca. 20 sec.

low voltage protection according to EN230

TF 802 2-stage operation

post-ignition time 2-4 sec.

TF 802.2 2-stage operation

post-ignition time 2-4 sec.

low voltage protection according to EN230

CONSTRUCTIONAL FEATURES

The control box circuitry is protected by a flame resistant,

transparent plastic housing. It incorporates the thermo-

mechanical, temperature compensated timer, flame check

and reset circuits.

Manual reset from lockout is provided by a push button with

an integrated lockout signal lamp. A central fixing screw

locks the control box to the wiring base. The wiring base and

control box have a positive plug-in arrangement, making it

impossible to achieve an incorrect connection between the

two parts. A variety of cable entry points provides utmost

flexibility of electrical wiring.

The TF 802.2 is fully compatible with the TF 701,

701-1 and TF 802. The flame detector IRD 910

must be replaced by its compatible type IRD

1010.

An optional extension button (item no. 70601)

compensates for height differences.

Satronic TF801- OIL BURNER

CONTROLLER

Oil burner control•

Plug in base (SA7531001)•

Single stage operation•

FZ 771 / IRD 1010 / UVD 970 Flame •

detector

Pre - purge 12 seconds•

Post ignition time 2 - 5 seconds•

Manual reset from lockout•

240 volt AC•

#SA02001

A Honeywell Company

300e/04 /98

For 1- or 2-stage oil power burners up to

30kg/h capacity and intermittent operations.

Flame detection:

- Photoresistor FZ 771 S

- Infrared-flicker detector IRD 1010

- UV solid state sensor UVD 970

Oil Burner Safety Control

TF 801 / 801.2

TF 802 / 802.2

TECHNICAL DATA

Operating voltage 220/240 V (-15..+10%)

50 Hz (40-60Hz)

Fuse rating 10 A fast, 6 A slow

Power consumption ca. 5 VA

Max. load per output

- terminal 3 1.5 A, cos ϕ 0.2

- terminal 4 4 A, cos ϕ 0.4

- terminal 5 0.5 A, cos ϕ 0.4

- terminal 6 0.5 A, cos ϕ 0.4

- terminal 7 0.1 A, cos ϕ 0.4

total load 5A, cos ϕ 0.4

Pre-purge time ca. 12 sec.

Pre-ignition time ca. 12 sec.

Post-ignition time TF 801/TF801.2 ca. 20 sec.

TF 802/TF802.2 ca. 2-4 sec

Delay time to oil valve 2 40 sec. (TF 802)

Lockout safety time 10 sec.

Reset time from lockout ca. 90 sec

Flame detector:

FZ 771 S red side-on viewing

FZ 771 S white side-on and end-on

viewing

Light sensitivity FZ 711S > 10 Lux

IRD 1010 side-on or end-on

viewing

UVD 970 end-on viewing

Weight incl. wiring base 0.25 kg

Mounting position any

Protection class IP44

Recommended ambient operating

temperature for control and

flame detector 0°C...+60°C

approved and certified according

to European standards

TF 801.2/TF802.2 EN 230

TF 801/TF802 DIN 4787

APPLICATION RANGE

The TF 801 or TF 802 oil burner safety control boxes are

suitable to control and monitor oil power burner up to 30 kg/

h capacity (approved and certified according to DIN 4787).

The control boxes TF 801.2 and TF 802.2 are approved and

certified according to EN230.

TYPES AVAILABLE

TF 801 1-stage operation

post-ignition time ca. 20 sec.

TF 801.2 1-stage operation

post-ignition time ca. 20 sec.

low voltage protection according to EN230

TF 802 2-stage operation

post-ignition time 2-4 sec.

TF 802.2 2-stage operation

post-ignition time 2-4 sec.

low voltage protection according to EN230

CONSTRUCTIONAL FEATURES

The control box circuitry is protected by a flame resistant,

transparent plastic housing. It incorporates the thermo-

mechanical, temperature compensated timer, flame check

and reset circuits.

Manual reset from lockout is provided by a push button with

an integrated lockout signal lamp. A central fixing screw

locks the control box to the wiring base. The wiring base and

control box have a positive plug-in arrangement, making it

impossible to achieve an incorrect connection between the

two parts. A variety of cable entry points provides utmost

flexibility of electrical wiring.

The TF 802.2 is fully compatible with the TF 701,

701-1 and TF 802. The flame detector IRD 910

must be replaced by its compatible type IRD

1010.

An optional extension button (item no. 70601)

compensates for height differences.

Satronic TF802- OIL BURNER

CONTROLLER

Oil burner control•

Plug in base (SA7531001)•

2 stage operation•

FZ 771 / IRD 1010 / UVD 970 Flame •

detector

Pre - purge 12 seconds•

Post ignition time 2 - 5 seconds•

Manual reset from lockout•

240 volt AC•

#SA02404

6.3

Section 6

1 2 3 4 5 6 7 8 ... 11 12

Section 6 1
Flame deteCtors 12

Comments to this Manuals

No comments

Siemens LFL Series User Manual Page 3

Comments to this Manuals

Related products and manuals for Unknown Siemens LFL Series