Siemens FUS1010 User Manual Page 196
- Page / 232
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7-2
1010NFM-3JSection 7
7.3 SELECT THE TRANSDUCER MOUNTING LOCATION
Select a mounting location that has a fully developed flow profile. Do not locate the transducer so that
sonic energy enters a region that is not representative of the flow velocities at the measuring location.
Use the figure below as a guide to select the proper mounting location.
Incorrect Transducer Placement Correct Transducer Placement
ELBOW
EXPANSION
OR
CONTRACTION
VALVE
ORIFICE PLATE
- SITRANS FUS 1
- 1010NFM-3J 1
- FIELD MANUAL 3
- Manual Changes 4
- MANUAL 5
- ADDENDUM 5
- Manual Addendum 6
- 1010FMA-4 6
- Use this menu to 10
- Manual Addendum 1010FMA-14 11
- 1010N-2 I/O Module 11
- FLOW COMPUTER 12
- INTERNAL 12
- CONNECTIONS 12
- TERMINAL STRIP 12
- TABLE OF CONTENTS 13
- 1. GETTING STARTED 21
- 22
- 1.5 THE 1010N KEYPAD 23
- 1.7.2 HOW TO ENTER DATA 25
- 1.7.3 THE METER TYPE MENU 28
- Ch1 [+/-] Ch2 29
- sensor types 32
- This block cursor is 33
- 1-14 34
- 1010NFM-3JSection 1 34
- 1.8 USING FASTSTART SETUP 35
- 1010WX METER TYPES 39
- 1010WX FLOWMETER LABEL 39
- SYSTEM HARDWARE 39
- 2.1 THE CHANNEL SETUP MENU 42
- 2.2 THE PIPE DATA MENU 46
- Section 2 47
- 2.2.6 LINER MATERIAL 50
- 2.2.7 LINER THICKNESS 50
- 2.3 THE APPLICATION DATA MENU 50
- °F (20°C) 50
- Use this menu cell to enter 51
- Use this menu cell to 53
- 2.3.2 UniMass TABLE 54
- 2.3.4 PIPE CONFIGURATION 59
- Spacer Bar PB-1 61
- Minimum 62
- 2.4.7 THE Ltn MENU CELL 65
- Drive 68
- =0 68
- 2.4.9 THE EMPTY PIPE SET MENU 69
- 2.4.10 ZERO FLOW ADJUST MENU 70
- Minimum Flow 73
- SmartSlew™ or Time 74
- Average output 74
- 2.5.3 MEMORY/FAULT SET 76
- 2.6 THE FLOW/TOTAL UNITS MENU 77
- 2-38 78
- 1010NFM-3JSection 2 78
- 2.6.1 FLOW VOLUME UNITS 79
- 2.6.2 FLOW TIME UNITS 79
- 2.6.3 FLOW DISPLAY RANGE 80
- 2.6.4 FLOW DISPLAY SCALE 80
- 2.6.5 TOTAL VOLUME UNITS 80
- 2.6.6 TOTALIZER SCALE 81
- 2.6.7 TOTAL RESOLUTION 81
- 2.6.9 BATCH/SAMPLE TOTAL 82
- 2.6.8 TOTALIZER MODE 82
- Use this menu to define 83
- 2.7.2 SET ALARM LEVELS 85
- 2.7.3 CALIBRATE FLOW RATE 88
- Point # (point 1 selected) 89
- Use this menu cell 90
- 2.8.3 TIME BASE 91
- 2.8.2 DATA DISPLAY 91
- 2.8.4 STRIPCHART CLEAR 92
- 2.9 THE DATALOGGER SETUP MENU 92
- 2.9.1 DATALOGGER MODE 94
- 2.9.2 DATALOGGER DATA 94
- 2.9.3 LOG TIME INTERVAL 95
- 2.9.4 DATALOGGER EVENTS 95
- 2.9.5 DISPLAY DATALOGGER 96
- 2.10.1 ANALOG OUTPUT SETUP 98
- 2.10.2 RELAY SETUP 100
- RELAY OPTION LIST 101
- 2.11.2 FLOW DATA MENU 104
- The M status is 106
- 2.11.4 THE LIQUID DATA MENU 107
- Using the [HF] Menu Item 109
- Detection Mode 113
- Envelope Signal 116
- TN marker 116
- Crossover Marker 116
- Command Line appears here 116
- Envelope Threshold 116
- 2.11.7 TROUBLESHOOTING TIPS 118
- *System Defaults 122
- Pipe Simulator 123
- ** See note below 124
- Transducer located 130
- Transducer located at 130
- 3 o'clock 130
- 3.1.4 PREPARING THE PIPE 131
- 1011 Series 134
- Transduce 134
- Spacer Bar 134
- Spring Clip 134
- Spacing Guide P/N Size 135
- End View 137
- Overlap Edge 138
- Mark (or fold) exactly 138
- CIRCUMFERENCE 138
- Minimum 139
- Reference Pin 140
- Shown Inserted 140
- Tension Screw 142
- TO SENSOR 144
- 4.1 PREFERRED UNITS 148
- This menu allows you 148
- 4.2 THE TABLE SETUPS MENU 149
- 4.2.1 PIPE TABLE 149
- 4.2.2 CREATE/EDIT PIPE 150
- 4.2.3 DELETE PIPE 151
- 4.3 TRANSDUCER TYPE MENU 151
- 4.4.1 DISPLAY DATALOGGER 153
- 4.4.2 OUTPUT DATALOGGER 154
- 4.4.3 CIRCULAR MEMORY 154
- 4.4.4 EST LOG TIME LEFT 155
- 4.4.5 CLEAR DATALOGGER 155
- 4.5 THE MEMORY CONTROL MENU 155
- 4.7 THE CLOCK SET MENU 159
- 4.7.1 DATE 159
- 4.7.2 TIME 159
- 4.8 RS-232 SETUP 160
- 4.8.1 BAUD RATE 160
- 4.8.2 PARITY 161
- 4.8.3 DATA BITS 161
- 4.8.4 LINE FEED 161
- 4.8.5 NETWORK ID 162
- 4.8.6 RTS KEY TIME 162
- 4.9 BACKLIGHT 162
- 4.10 SYSTEM INFO 162
- 354.6597 164
- 5.3.1 PIPE DIMENSIONS 167
- 5.3.3 FLOW VELOCITY RANGE 167
- 5.3.5 ACCURACY 168
- 5.3.6 REPEATABILITY 168
- 5.3.7 DATA STABILITY 168
- 5.4 FLOW CONDITIONS 169
- 5.4.1 LOW FLOW RATES 169
- 5.4.5 LIQUID COMPATIBILITY 170
- 5.4.6 AERATION 170
- 5.4.7 SLURRIES 171
- 5.4.8 TWO-PHASE LIQUIDS 171
- 5.4.9 VISCOUS LIQUIDS 171
- 5.6 REFERENCE TABLES 172
- (continued) 173
- 5-14 179
- Section 5 179
- Number Index 180
- 5-16 181
- 2.7.3 Calibrate Flow Rate.) 186
- 6-12 194
- 1010NFM-3JSection 6 194
- Connect to UP 197
- Channel 1 Clamp-on 198
- Channel 2 >Reflexor 198
- Dual Channel Flow 198
- CURSOR USAGE TIPS 200
- ADJUSTMENT FUNCTION NOTE 201
- 7.13 REFLEXOR DIAGNOSTIC DATA 202
- DIAGNOSTIC DATA 202
- 7.16 OTHER MENU ENTRIES 203
- APPENDIX A 204
- Couplant 204
- Installation 204
- Instructions 204
- APPENDIX B 206
- Select Meter Type 211
- Meter Facilities 211
- APPENDIX C 215
- ENGINEERING DRAWINGS 215
- Index-10 226
- Index-11 227
- Index-12 228
- TRADEMARKS 229
- DUCTILE IRON PIPE 230
- Wall 0.279 0.312 0.312 0.937 231
Related products and manuals for Measuring, testing & control Siemens FUS1010
(183 pages)
(22 pages)
(22 pages)© 2020, manymanuals.com. All rights reserved. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals