Siemens B8732.0 User Manual download pdf

REV24..

Operating instructions

REV24.. - 7-day room temperature controller for the right temperature at the right time. All factory

settings already provide optimal living comfort. You can easily adjust the controller to your needs

with the user-assisted clear-text display and program selection slider.

Note the following for placing the controller:

• Make sure no other influencing factors influence the controller's temperature sensor (no solar radiation and

other heat or cold source influences).

Info button

Increase values, set time or

make a selection

Change between Comfort and

energy saving temperature

(active until next switching time)

and Part

function

Decrease values, set time or

make a selection

Operating mode

selector:

- Automatic

- Exception day

- Comfort mode

- Energy saving

mode

- Protection

mode

Program selection slider

RUN

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Operating elements and settings

Time setting

Date

Day / Month / Year

Weekdays 1-5

Weekend 6-7

Individual da

s 1..7

1, 2 or 3

Comfort phases

Start time

Comfort phase 1

Temperature

Comfort phase 1

End

Comfort phase 1

Start time

Comfort phase 2

Temperature

Comfort phase 2

End

Comfort phase 2

Start time

Comfort phase 3

Temperature

Comfort phase 3

End

Comfort phase 3

Saving temp. time

program

Start

Absence

Temperature

Absence

End

Absence

Temperature

remote control

Slider positions

If the selected operating mode does not support the setting, the time display shows PASS.

Special symbols displayed

The controller display can show the following special symbols:

Is symbol displayed ?

The alarm indicates an error!

Press the Info button and check the error message (e.g. radio clock signal, radio connection to receiver, etc.).

Contact a specialist as needed.

Is symbol displayed ?

This symbol tells you that you must exchange the batteries within the next 3 months.

Insert 2 new alkaline batteries type AA, 1.5 V as follows:

Remove the controller from the mounting base; open the battery compartment on the rear; remove the old

batteries; insert the new batteries and reinsert the controller in the base.

Caution: Time and date are retained for max. 1 minute.

(All other settings are fixed and remain unchanged!)

Dispose of the batteries as per regulations.

Is symbol displayed ?

The radio clock symbol only appears if the receiver is set up and activated to receive the

time signal from Frankfurt (Germany). A permanent symbol indicates that both time and

date of the controller are synchronized to Frankfurt (DCF77).

The symbol flashes if the signal is not received for more than 1 week.

Is symbol or displayed ?

The controller is in "heating mode“ or "cooling mode“ .

Commission the controller and quick start

The controller contains a factory-set comfort switching pattern and temperature values.

Proceed as follows for initial commissioning:

Remove the controller from the mounting base and pull off the black insulating

tape from the 2 batteries: The controller turns on automatically. Reinsert the

controller in the mounting base.

After startup, a welcome message appears for ca. 2 minutes. Press a button

to interrupt the message. Language selection starts with “ENGLISH“ (factory

setting). Press

or until your language appears. Press or move

the slider to accept your language.

Slider in position 1 (time setting): Press or to set the time.

Note: You do not need to enter the time when DCF77 receiver for the

time signal from Frankfurt (Germany) is equipped.

Slider in position 2 (date: day/month/year): Press or to set the date.

Note: You do not need to enter the date when DCF77 receiver for the

time signal from Frankfurt (Germany) is equipped.

RUN

Move the slider to the very right to position RUN (only way to close the cover).

Set the operating mode with the operating mode selector.

Factory setting is

Fold the operating instructions and reinsert in the mounting base.

Turn on display lighting, check error messages or other important

information

Press the Info button once to activate display backlighting. Backlighting

goes off automatically after a short time.

Continuing to press the Info button activates the information display:

is lit. The device first shows pending error messages and then important

information (e.g. switching programs, ...).

Change the temperature level in the time switch program,

or are you not at home for a while?

In the time switch program, press this button to change from the current

temperature level to the next and back.

Quickly activate energy saving temperature when you leave the apartment

briefly to save energy.

The change appears on the display. It is valid only until the next switching

time.

Tips to save energy without reducing comfort

• Heat your rooms to max 21 °C.

• Use to switch to energy saving temperature even if you are absent only briefly.

• Air out your rooms briefly, but with wide-open windows.

Day of week

Low battery

Radio Clock Date Setting: 1-5, 6-7, 1..7/

active Reading: 1..7

Time display

Remote control active

Holiday mode

Display

Info mode

Installer mode

Temperature

setpoint symbols

Text display

Alarm

Cooling mode /

Heating mode

Switching pattern

with time cursor

Automatic mode

Party mode active

Exception day mode

Continuous comfort mode

°C or °F

Continuous energy

saving mode

Heating On /

Cooling On

Protection mode

Temperature display

B2205en 25.12.2007 Siemens, Building Technologies

1 2

Operating instructions 1

Summary of Contents

Page 1 - Operating instructions

REV24.. Operating instructions REV24.. - 7-day room temperature controller for the right temperature at the right time. All factory settings alread

Page 2

Select operating mode Press the operating mode button to select one of 5 modes. Operating modes with time program The controller offers both time pr

Comments to this Manuals

No comments

Siemens B8732.0 User Manual

Browse online or download User Manual for Ovens Siemens B8732.0. REV24.. Operating instructions

Summary of Contents

Comments to this Manuals

Related products and manuals for Ovens Siemens B8732.0