Siemens MICROMASTER 440 User Manual Page 27
- Page / 78
- Table of contents
- BOOKMARKS
- MICROMASTER 440 1
- Warnings, Cautions and Notes 2
- Contents 3
- 1 Installation 5
- 2 Electrical Installation 6
- 2.2 Power Terminals 13
- Frame Sizes B and C 14
- Frame Sizes D and E 15
- Frame Size F 16
- Frame Sizes FX and GX 17
- MICROMASTER 440 18
- 2.3 Control terminals 21
- External 24 V 22
- Analog output 23
- Remove I/O board 23
- DIP50/60 23
- 4.3 Bus interface (CB) 25
- BOP / AOP (Option) 26
- 6 Commissioning 28
- P0310 = 29
- P0311 = 29
- P0335 = 29
- P0640 = 29
- P0700 = 29
- P1135 = 30
- P1500 = 31
- P3900 = 1 31
- P0003 = 3 34
- P2010 = 34
- P2011 = 34
- P2012 = 34
- P2013 = 34
- 6.4.3 Digital input (DIN) 35
- 52.0 Drive ready 0 36
- 52.1 Drive ready to run 0 36
- 52.2 Drive running 0 36
- P1000 = 37
- 6.4.6 Analog input (ADC) 38
- P0773 = 39
- Setpoint memory of the MOP 40
- Setpoint of the MOP 40
- 6.4.9 Fixed frequency (FF) 41
- JOG frequency right 42
- JOG frequency left 42
- JOG ramp-up time 42
- JOG ramp-down time 42
- P0292 = 45
- Motor temperature sensor 46
- Motor overload factor [%] 46
- P0408 = 47
- P0491 = 47
- P0492 = 47
- P0400 = 47
- Control mode 48
- CO: Upper torque limit 50
- CO: Lower torque limit 50
- Motoring power limitation 50
- Control word of motor model 52
- Filter time for act. speed 53
- Gain speed controller 53
- Frequent settings: 54
- Flying start 55
- Automatic restart 55
- Holding brake enable 56
- P0731=52.C 57
- P0748 = 0 57
- BI: Enabling the DC brake 58
- P1232 = 58
- P1236 = 59
- Dynamic braking 60
- P1240 = 60
- 6.4.18.9 PID controller 63
- Controller structures 64
- PID cancer control 65
- Technological application 66
- Gearbox ratio input 66
- Gearbox ratio output 66
- No. of shaft turns = 1 Unit 66
- P2800 = 67
- P2802 = 67
- Timer 1 68
- Timer 2 68
- Timer 3 68
- Timer 4 68
- BI: CDS bit 1 69
- Example for CDS changeover: 69
- Drive data set (DDS) bit 0 70
- BI: DDS bit 1 70
- Example: 71
- 6.4.20 Diagnostic parameters 72
- CO/BO: Control word 1 73
- CO: Actual frequency 73
- CO: Act. output voltage 73
- 6.5 Series commissioning 75
- 7 Displays and messages 76
- Regional Contacts 78
- Central Technical Support 78
- Internet Address 78
© 2020, manymanuals.com. All rights reserved. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals