Siemens CA 373 Series Service Manual

Selection And Application GuideThe LCP3000EZ System Based on InstabusEIB TechnologyFully Modularlighting controlSYSTEM

LCP3000EZ Lighting Control SystemSelection Process 5WG1 70 –8X –Z Enclosure HeightPanel DesignationNumber of Input ModulesNumber of Output Modul

LCP3000EZ Lighting Control SystemSelection ProcessSWG1 373-5EY01 -Z-A20216 channel time clockSWG1 254-3EY01 -Z-A203Outdoor ambient light level sensorS

The LCP E-Z-Config Tool is a software program developed by Siemens to allow installers to easily configure theLCP3000EZ lighting control system. It is

12EnclosuresThe Siemens Instabus lighting control panel supports thesystem components and other panel mounted devices.All panel mounted devices snap i

Load Switch N 512The load switch N 512 is an N-systemDIN rail mounted device. Via its eightoutputs, it can switch eight separategroups of electric dev

14Binary Input N 261The binary input N 261 is an N-systemDIN rail mounted device with fourinputs. The inputs require 24 AC orDC; this voltage is provi

Annual Scheduler REG 372The 4-channel time switch REG 372 is a DIN rail mounted device for mounting in distribution boards. Theconnection to system is

16Annual Scheduler REG 373The 16-channel time switch REG 373 (annual scheduler) is a DIN rail mounted device. The connection to system is made via a b

Power Supply Unit N 123 320 mAThe power supply unit N 123 providesand monitors the necessary Class 2power for each panel. Power supplyunits are mounte

18Choke N 120 — 500 mAThe bus devices working voltage istransmitted via the same cable as thedata. The choke N 120 protects thesedata from becoming te

LCP3000EZ Lighting Control SystemTable of ContentsInstabus EIB Technology 2System Overview 3Selection Process 4 – 10E-Z-Config Tool 11System Component

Interface N 148/04 RS 232The RS 232 interface N 148/04 is a N-system DIN rail mounted device.The device is connected to the busline via the pressure c

20Connector REG 191/01/11The connector module REG 191/01provides the connection between thedata rails within a panel or betweenpanels throughout the b

Dual Sensor AP 254The Dual Sensor AP 254 providesambient light level and outdoor temperature values. These values can be read on a computer with theop

22Motion Detector UP 255The motion detector UP 255 is a proximity sensor which reacts tomovements of people, animals orother moving objects. If a moti

23Switch Interface UP 220The switch interface UP 220 is a binary input device for installation in a standard junction or wall switchbox. Four inputs a

Touch Panel Vision UP 588The touch panel vision UP 588 is amultifunctional display/control unit.The basis of the device is an LC displaywith a resolut

Ethernet Interface N148/21The Ethernet interface N148/21 is aDIN rail mounted device. It enablesconnections to LCP3000EZ via datanetworks using the In

Siemens Energy & Automation, Inc.3333 Old Milton ParkwayAlpharetta, GA 300051-800-964-4114 [email protected]/powerLCSA-LCP01-

About This GuideThis Selection and Application Guide helps you select thecorrect number of LCP3000EZ panels, inputs, outputs andaccessories to fit you

System OverviewThe LCP3000EZ Lighting Control System is fully modular indesign. In its basic form, it consists of ten network able lowvoltage relay co

Part 1: Plan the ProjectSelecting LCP3000EZ Panels and Accessories This section describes the application selection process forthe Siemens LCP3000EZ L

LCP3000EZ Lighting Control SystemSelection Process RELAY OUTPUTS LCP3000EZ ARelayPanelboard Ckt Relay Description Control Logic

LCP3000EZ Lighting Control SystemSelection Process RELAY OUTPUTS LCP3000EZ ARelayPanelboard Ckt Relay Description Control Logic

LCP3000EZ Lighting Control SystemSelection Process Information Form Sample 2 — Time Clock Schedules (Weekly)Time Clock Schedules (Weekly Schedule)Sche

8LCP3000EZ Lighting Control SystemSelection Process Information Form Sample 2 — Time Clock Schedules (Weekly)Time Clock Schedules (Weekly Schedule)Sch