Siemens Sinumerik 810T User Manual Page 273
- Page / 312
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4 Monitoring Functions 11.90
4.6 Listing of the alarms/alarm description
Alarm No.
Alarm Text:
3028
”Too many fields/variables”
Remarks: Alarm only on commissioning
Alarm No.
Alarm Text:
3029
”Graphics option not available”
Reason:
Remedy:
Explanation:
Graphic elements have been projected into the selected display, but
the ”Graphics” option is not fitted in the control
– Retrofit ”Graphics” option
– Only project display without graphic elements
Only with additional programming developed in WS 800
Alarm-No.
Alarm Text:
3030
”Cursor memory not available”
Reason:
Remedy:
Explanation:
The cursor memory programmed for the display selected is not correct
(number not allowed or too large).
Use the workstation to redefine the cursor memory
– The function of the cursor memory is to position the cursor where it
was previously when the display is called again.
– Only with additional programming via WS 800
Alarm-No.
Alarm Text:
3032
”Too many fields / variables”
Remarks: Alarm only on commissioning
Alarm-No.
Alarm Text:
3033
”Display text not available”
Reason:
Remedy:
Explanation:
An error has occurred while linking with the workstation.
Check link list, and relink with the workstation (to clear link error).
– Only with additional programming via WS 800
– Alarm only on commissioning
Alarm-No.
Alarm Text:
3034
”Text not available”
Explanation: – Only with additional programming via WS 800
– Alarm only on commissioning
Alarm-No.
Alarm Text:
3040
”Fields / var. not displayable”
Explanation: – Only with additional programming via WS 800
– Alarm only on commissioning
Alarm-No.
Alarm Text:
3041
”Too many fields / variables”
Remarks: Alarm only on commissioning
4-30
© Siemens AG 1990 All Rights Reserved 6ZB5 410-0EP02
SINUMERIK 810T, GA3 (BN)
- SINUMERIK 810T 1
- Operating and Programming 1
- SINUMERIK 3
- Basic Version 3 3
- Software Version 3 3
- Part 1: Operating 3
- Documentation 5
- Preliminary Remarks 6
- Contents 10
- 1 General Notes 14
- 2 Operation 17
- Keys below the CRT display 19
- 2.1.1.2 Display panel 20
- 01.93 2 Operation 21
- 2 Operation 09.91 22
- Numeral: 3 25
- 2 Operation 11.90 26
- 2.1.1.5 Control keys 27
- Is channel changeover used ? 29
- (( Bild 1 von Druckerei 30
- 09.91 2 Operation 31
- 11.90 2 Operation 33
- - the maximum spindle speed 34
- - continuous mode or 36
- - jog mode 36
- Section of the CRT display: 37
- 1:1 mittig einmontieren)) 41
- ((Foto - Nr. 87 E 3840 42
- 2.2 Switching on / off 52
- ”AUTOMATIC” basic display 54
- ”JOG” basic display 55
- ”MDI AUTOMATIC” basic display 55
- ”REFPOINT” basic display 55
- ”PRESET” basic display 56
- ”REPOS” basic display 56
- ... Reset 62
- ... No Reset) 62
- Selected MODE 66
- 2.4 Operating mode menu trees 67
- 2.4.1 ”AUTOMATIC” mode 68
- 2.4.1 ”AUTOMATIC” mode 69
- 2.4.2 ”JOG” mode 70
- 2.4.2 ”JOG” mode 71
- 2.4.3 ”JOG” mode 73
- 2.4.4 ”MDI AUTOMATIC” mode 74
- 2.4.5 ”REFPOINT” mode 75
- 2.4.5 ”REFPOINT” mode 76
- 2 Operation 01.93 78
- OVER- > 79
- 2.4.7 ”PRESET” mode 80
- 2.4.7 ”PRESET” mode 81
- 2.4.8 ”REPOS” mode 82
- 2.4.8 ”REPOS” mode 83
- (PLC MACHINE DATA) 93
- TOOL DATA 97
- ZO AUTOM 98
- ZERO OFFSET 98
- 3 Operating Sequences 99
- 3.1 Preparation 100
- 3.1.1 Switching on 100
- Sequence of operation 100
- (( 810T)) 101
- (( Bild 6 von Druckerei 101
- 3.1.4 Tool offset 102
- 3.1.4.1 Input of tool offset 102
- 3.1.3 Tools 102
- 0 Tool number 103
- 1 Tool type 103
- 3 Operating Sequences 01.93 104
- 3.1.4 Tool offset 104
- SINUMERIK 810T, GA3 (BN) 104
- L2 Basic 105
- L1 Basic 105
- Sequence of operation 105
- 3 Operating Sequences 09.91 106
- 09.91 3 Operating Sequences 107
- 11.90 3 Operating Sequences 108
- 3 Operating Sequences 11.90 109
- 3.1.4.4 Automatic tool offset 110
- ((Bild 810T/17 einmontieren)) 110
- 3.1.4.6 Input of tool data 112
- ((Bild 810T/15 einmontieren)) 112
- ((Bild 810T/58 einmontieren)) 113
- 3.1.4.7 Display of tool data 114
- 3.1.5 Zero offset 116
- 3.1.5.1 Settable zero offsets 117
- (( Bild 18 von Druckerei 117
- 3.1.5 Zero offset 118
- - external zero offset 119
- ((Bild 810T/20 einmontieren)) 120
- Setting data ”R PARAMETERS” 122
- AXIAL” setting data 130
- (( Bild 24von Druckerei 131
- 3.1.8 Axis synchronization 136
- 3 Operating Sequences 09.91 137
- 3.1.8 Axis synchronization 137
- TRANSMIT function 142
- 3.1.10 Program input 143
- 3.1.10 Program input 144
- 3 Operating Sequences 11.90 145
- 3.1.11 Contour 151
- 3.1.11 Contour 152
- 157
- 3.1.13 Program management 160
- ((Bild 810T/30einmontieren)) 160
- 3.1.13 Program management 163
- “DELETE” 165
- 01.93 3 Operating Sequences 174
- 3.1.14 ”SIMULATION” 175
- 3.1.14 “SIMULATION” 176
- 1.14.2 Influencing simulation 177
- 3.1.15 Data input/data output 180
- 3.1.15.1 Setting data bits 181
- 1 1 0 0 0 1 0 0 181
- ... ... 182
- MeaningData type 184
- (( Bild 39 von Druckerei 186
- >PART 187
- 3.1.16 NC in two languages 191
- 3.2 Machining 192
- (( Bild 13 von Druckerei 194
- (( Bild 42 von Druckerei 195
- Single blockBlock type 200
- (( Bild 44 von Druckerei 202
- 3.2.3.2 ”OVERSTORE” 203
- (( Bild 46 von Druckerei 203
- 3.2.3.3 ”BLOCK SEARCH” 205
- (( Bild 49 von Druckerei 209
- (( Bild 48 von Druckerei 213
- (( Bild 50 von Druckerei 215
- Important: 220
- 3.2.5 ”TEACH IN” 221
- 3.2.6 ”PLAYBACK” 223
- 3.2.6 “PLAYBACK” 224
- 3.2.7 ”JOG” mode 227
- 3.2.9 ”HANDWHEEL” 230
- (( Bild 53 von Druckerei 231
- 3.2.10 “DRF” 232
- 3.2.10 ”DRF” 233
- (( Bild52 von Druckerei 233
- - by switching on the control 235
- (( Bild 9 von Druckerei 239
- 3.2.13 Scratching 241
- 4 Monitoring Functions 242
- 4.3 Display representation 243
- ORD12 Contour Monitoring 243
- 11.90 4 Monitoring Functions 244
- 4.3 Display representation 244
- 4 Monitoring Functions 11.90 248
- 11.91 4 Monitoring Functions 249
- 4 Monitoring Functions 09.91 250
- 01.93 4 Monitoring Functions 253
- 4 Monitoring Functions 01.93 254
- */–* SW overtravel switch” 254
- 09.91 4 Monitoring Functions 259
- 5 Maintenance 277
- 5 Maintenance 01.93 278
- 5.2 Handling the modules 278
- 5.4 CRT display 279
- 5.5 Cleaning 280
- 6 Data Interfaces 281
- 7654 3210 282
- 6.4 Device connection data 285
- 6 Data Interfaces 01.93 286
- 6.4 Device connection data 286
- 11.90 6 Data Interfaces 287
- 7 Interfacing to the Machine 288
- Precludes PLC 289
- 7.2 Ordering data - Options 290
- 7.3.1 General machine data 292
- 7.3.1 General machine data 293
- 7.3.3 Machine data bits 296
- 0 0 0 0 0 0 0 1 296
- 7.3.3 Machine data bits 297
- 7.4 Setting data 300
- 7.4.1 General SD bits 300
- 7.4.2 Axis-specific bits 300
- * Significance of ”x”: 301
- 0=Spindle 1 301
- 1=Spindle 2 301
- 8 Appendix 302
- Mnemonics Meaning 303
- 8.2 List of terms used 304
- 8 Appendix 09.91 305
- 8.2 List of terms used 305
- 09.91 8 Appendix 306
- 01.93 8 Appendix 310
© 2020, manymanuals.com. All rights reserved. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals