Siemens SED2 Operations Instructions Page 11
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
11/126
Siemens Building Technologies SED2 variable speed drives CM1U5192en
HVAC Products Safety instructions 01.2002
2 Safety instructions
The following warnings and notes on danger are provided for your safety and as a
means of preventing damage to the product or to any components of the connected
machinery. This section contains general warnings, preventive measures, and danger
warnings, which apply to all work on the SED2 variable speed drives. Specific warnings
applicable to particular tasks are summarized at the beginning of each chapter and
repeated throughout the chapter as necessary at the relevant points.
Please read this information carefully, as it is provided for your personal safety,
and to help extend the life of the SED2 variable speed drive and any equipment
connected to it.
Refer to section 1.6 Document conventions for information on the format of warning
notes and associated symbols.
2.1 General
♦ This equipment uses hazardous voltages and drives potentially dangerous rotating
mechanical parts. Non-compliance with warnings or failure to follow the
instructions in this manual may put lives at risk, or result in severe physical injury,
or serious damage to property/equipment.
♦ Only authorized personnel may work on this equipment. They must first acquaint
themselves with all the safety instructions, and installation and operating
instructions in this manual. Successful and safe operation of this device depends
on its proper handling, installation, commissioning, and operation.
♦ Prevent children and other unauthorized persons from accessing the equipment.
The DC link capacitors remain charged with dangerous voltages for five minutes after
power has been switched off.
Do not open the device for five minutes after switching off the supply voltage.
Use the equipment only for purposes as specified by the manufacturer. Unauthorized
modifications and use of spare parts or accessories not supplied or recommended by
the manufacturer of this equipment may cause fires, electric shock, and physical injury.
Keep these operating instructions within easy reach of the equipment and make them
available to all users.
2.2 Commissioning
♦ Only authorized personnel trained in the setup, installation, commissioning, and
operation of the product may work on the product and plant.
♦ Only hard-wired mains connections are permissible. Ground the VSD (IEC 536,
Class 1, NEC and other relevant industry standards).
♦ If a residual current device (RCD) is to be used, it must be a type B device.
♦ Do not connect machines with a 3-phase power supply fitted with EMC filters to the
mains via an earth leakage current circuit breaker (ELCB) (see DIN VDE 0160,
section 6.5).
Format of warnings
Warning
Risk of electric shock
Danger
Purpose
Availability of the
operating instructions
- SED2 variable speed drives 1
- Operating instructions 1
- HVAC Products 01.2002 2
- Table of contents 3
- 1 Introduction 7
- 1.6 Document conventions 8
- 2 Safety instructions 11
- 2.3 Operation 12
- 2.4 Repairs 12
- 3 Mechanical installation 13
- 3.3 Mounting 14
- 5192M01en 17
- 4 Electrical installation 19
- Torx driver T20 21
- Torx screwdriver 22
- SPS: Programmable controllers 23
- Cable routing for frame 24
- Shield connected 25
- Motor cable 25
- Incoming mains voltage 25
- Removing the 27
- I/O module 27
- Removing the cover of the 27
- Removing the operator 28
- Opening the housing: 28
- Frame sizes D and E 28
- FramesizeF 29
- (Ground) 30
- DC+DC+DC+DC- B 31
- R+ B+ B+ 31
- L3 U V WL2L1 31
- Access to the mains 32
- PE L1 L2 L3 34
- Mains voltage inputs 34
- EMC filter 34
- 1 (17) 10 (7) 1 (17) 10 (7) 35
- 4.3.9 Direction of rotation 36
- 5192Z11en 37
- 4.4 Control terminals 38
- 4.5 SED2 block diagram 39
- 5 Commissioning 41
- 5.1.1 DIP switch settings 42
- 5.2 Checklist prior to start 43
- ≥ motor rating? 43
- Operator 45
- Function Effects 45
- 5.4 Commissioning modes 46
- Resulting display 49
- 5.4.7 10 Hz test 50
- 5.4.8 General operation 51
- 6 Programming 53
- See AOP operating 54
- 6.3.1 Digital inputs 55
- DIN6 DIN5 56
- DIN4 DIN3 56
- DIN2 DIN1 56
- 6.3.2 Analog inputs 57
- Signal in % 58
- Time in ms 58
- 6.3.3 Analog outputs 60
- 6.3.6 OFF functions 63
- 6.3.7 Control types 63
- 6.3.8 Communication 63
- 6.4.1 PID controller 64
- CONTROLLER 64
- 5192Z22en 65
- 5192D01en 66
- 5192Z23en 67
- 6.4.4 Staging pumps or fans 68
- Demand or volume flow 69
- 5192D04en 71
- 6.4.6 Bypassing the VSD 73
- P1264 P1262 P1262P1263 74
- 6.4.7 Hibernation mode 75
- P0508[4] Unit 82
- 7 Troubleshooting 107
- 7.2 Error messages 108
- ≤ VSD power (P0206) 108
- 8 Technical data for the SED2 113
- 8.2 Type-specific data 115
- 9 Appendix 119
- 9.2 Applicable standards 120
- 9.3 List of abbreviations 121
- HVAC Products Index 01.2002 123
Related products and manuals for TVs & monitors Siemens SED2
TVs & monitors Siemens SED2 Specifications
(132 pages)
(132 pages)
TVs & monitors Siemens SED2 User Manual
(8 pages)
(8 pages)
TVs & monitors Siemens CMCC2120 User Manual
(14 pages)
(14 pages)
TVs & monitors Siemens 463V FA User Manual
(31 pages)
(31 pages)
TVs & monitors Siemens 175V Service Manual
(36 pages)
(36 pages)
TVs & monitors Siemens 463V FA User Manual
(34 pages)
(34 pages)
TVs & monitors Siemens 43B1-M User Manual
(32 pages)
(32 pages)
TVs & monitors Siemens FT2014 Specifications
(14 pages)
(14 pages)
TVs & monitors Siemens SED2 Service Manual
(154 pages)
(154 pages)
TVs & monitors Siemens NCM S7 User Manual
(255 pages)
(255 pages)
TVs & monitors Siemens NCM S7 User Manual
(188 pages)
(188 pages)
TVs & monitors Siemens CMTC1913 User Manual
(18 pages)
(18 pages)
© 2020, manymanuals.com. All rights reserved. | 1.516 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals